The SRS warning light is located in the combination meter.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).
After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).
Check if a CAN communication DTC is output.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTCs are output (w/ Central Gateway ECU) | B |
| DTCs are output (w/o Central Gateway ECU) | C |
A
B
C
Measure the voltage of the battery.
11 to 14 V
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and combination meter.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G1-21 (IG2) - G1-25 (E1) | Ignition switch ON | 11 to 14 V |
| G1-21 (IG2) - G1-26 (E2) | Ignition switch ON | 11 to 14 V |
| *a | Rear view of wire harness connector
(to Center Airbag Sensor) |
OK
NG
for 5L-E:
| *a | Front view of wire harness connector
(to Combination Meter) |
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the G6 connector from the combination meter.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-28 (IG+) - G6-21 (E2) | Ignition switch ON | 11 to 14 V |
| G6-26 (B) - G6-21 (E2) | Always | 11 to 14 V |
except 5L-E:
| *a | Front view of wire harness connector
(to Combination Meter) |
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the G304 connector from the combination meter.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G304-22 (IG+) - G304-20 (E2) | Ignition switch ON | 11 to 14 V |
| G304-21 (B) - G304-20 (E2) | Always | 11 to 14 V |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the combination meter.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the SRS warning light condition.
Make sure that nobody is in the vehicle.
After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.
The primary check period is approximately 6 seconds after the ignition switch is turned to ON.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)