Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Any of the following conditions are met:
·

"Spiral Cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Steering sensor CAN branch wire or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

C447922E01
5.604,0.99 6.219,1.188 0.615,0.198 10 false CANH 5.615,1.573 6.229,1.771 0.615,0.198 10 false CANL 5.625,2.729 6.24,2.927 0.615,0.198 10 false BAT 5.625,3.552 6.24,3.75 0.615,0.198 10 false IG 5.604,5.125 6.219,5.323 0.615,0.198 10 false ESS 5.375,0.844 5.531,1.042 0.156,0.198 10 false 3 5.365,1.448 5.521,1.646 0.156,0.198 10 false 2 5.375,2.604 5.531,2.802 0.156,0.198 10 false 5 5.375,3.458 5.531,3.656 0.156,0.198 10 false 4 5.365,4.979 5.521,5.177 0.156,0.198 10 false 1 2.167,0.771 2.594,1.146 0.427,0.375 10 false 2*4 1.708,0.781 2.063,1.083 0.354,0.302 10 false 9*3 5.51,5.938 6.073,6.208 0.563,0.271 10 false G205 5.5,6.115 7.083,6.594 1.583,0.479 10 false Steering Sensor 2.115,0.979 2.76,1.281 0.646,0.302 10 false G286 0.302,1.969 2.365,2.385 2.063,0.417 10 false No. 6 CAN Junction Connector*3, No. 2 CAN Junction Connector*4 4.083,2.573 5.615,2.771 1.531,0.198 10 false ECU-B 2.188,2.708 3.073,2.917 0.885,0.208 10 false from Battery 3.844,3.448 4.844,3.667 1,0.219 10 false ECU-IG NO.1 1.635,3.563 4.25,3.854 2.615,0.292 10 false from IG NO.1 Relay*1 2.104,1.563 2.75,1.865 0.646,0.302 10 false G286 1.667,0.99 2.313,1.292 0.646,0.302 10 false G290 1.656,1.563 2.302,1.865 0.646,0.302 10 false G290 2.146,1.354 2.573,1.729 0.427,0.375 10 false 12*4 1.677,1.354 2.031,1.656 0.354,0.302 10 false 19*3 0.833,4.24 3.448,4.531 2.615,0.292 10 false from Engine Stop and Start ECU*2 0.344,5.219 2.958,5.51 2.615,0.292 10 false *1: w/o Stop and Start System 0.323,5.646 2.938,5.938 2.615,0.292 10 false *2: w/ Stop and Start System 0.323,6.063 2.938,6.354 2.615,0.292 10 false *3: for LHD 0.323,6.458 2.938,6.75 2.615,0.292 10 false *4: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING SENSOR BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C382824C01
1.438,0.135 1.875,0.427 0.438,0.292 1.167,1.75 1.333,1.75 1.333,1.75 1.531,1.302 true 2.073,1.75 1.906,1.75 1.906,1.75 1.719,1.281 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.458,0.208 1.896,0.427 0.438,0.219 10 false G205 0.771,1.677 1.208,1.896 0.438,0.219 10 false CANL 2.135,1.667 2.573,1.885 0.438,0.219 10 false CANH
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-3 (CANH) - G205-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C


A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR

C

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C382824C02
1.438,0.135 1.875,0.427 0.438,0.292 1,1.75 1.167,1.75 1.167,1.75 1.365,1.302 true 2.219,1.75 2.052,1.75 2.052,1.75 1.865,1.281 true 2.479,1.417 2.313,1.417 2.313,1.417 2.052,1.219 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.458,0.208 1.896,0.427 0.438,0.219 10 false G205 0.677,1.677 1.115,1.896 0.438,0.219 10 false ESS 2.271,1.667 2.708,1.885 0.438,0.219 10 false IG 2.552,1.344 2.99,1.563 0.438,0.219 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G205-5 (BAT) - Body ground Always 11 to 14 V
G205-4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR
a.
C382824C02
1.438,0.135 1.875,0.427 0.438,0.292 1,1.75 1.167,1.75 1.167,1.75 1.365,1.302 true 2.219,1.75 2.052,1.75 2.052,1.75 1.865,1.281 true 2.479,1.417 2.313,1.417 2.313,1.417 2.052,1.219 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.458,0.208 1.896,0.427 0.438,0.219 10 false G205 0.677,1.677 1.115,1.896 0.438,0.219 10 false ESS 2.271,1.667 2.708,1.885 0.438,0.219 10 false IG 2.552,1.344 2.99,1.563 0.438,0.219 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G205-5 (BAT) - Body ground Always 11 to 14 V
G205-4 (IG) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IG terminal) B
NG (Other terminal) C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)