Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Any of the following conditions are met:
·

"Engine (ECM)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

ECM CAN main wire or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

for 1GR-FE with Manual Transmission:


C382818E01
0.427,0.99 1.042,1.188 0.615,0.198 10 false G290 0.427,1.156 1.646,1.51 1.219,0.354 10 false No. 6 CAN Junction Connector 5.833,0.323 6.448,0.521 0.615,0.198 10 false CANH 5.823,0.958 6.438,1.156 0.615,0.198 10 false CANL 5.802,1.375 6.417,1.573 0.615,0.198 10 false BATT 5.813,1.771 6.427,1.969 0.615,0.198 10 false +B 5.813,2.177 6.427,2.375 0.615,0.198 10 false +B2 5.813,2.583 6.427,2.781 0.615,0.198 10 false MREL 5.823,2.99 6.438,3.188 0.615,0.198 10 false EC 5.813,3.385 6.427,3.583 0.615,0.198 10 false ME01 5.823,3.76 6.438,3.958 0.615,0.198 10 false E02 5.823,4.167 6.438,4.365 0.615,0.198 10 false E1 5.823,4.563 6.438,4.76 0.615,0.198 10 false E01 5.458,4.563 6.073,4.76 0.615,0.198 10 false C37 5.458,3.771 6.073,3.969 0.615,0.198 10 false C37 5.469,3.385 6.083,3.583 0.615,0.198 10 false C37 5.458,4.167 6.073,4.365 0.615,0.198 10 false C36 5.448,2.979 6.063,3.177 0.615,0.198 10 false G55 5.448,2.583 6.063,2.781 0.615,0.198 10 false G55 5.448,2.188 6.063,2.385 0.615,0.198 10 false G55 5.448,1.771 6.063,1.969 0.615,0.198 10 false G55 5.448,1.365 6.063,1.563 0.615,0.198 10 false G55 5.438,0.802 6.052,1 0.615,0.198 10 false G56 5.448,0.438 6.063,0.635 0.615,0.198 10 false G56 5.51,0.25 6.125,0.448 0.615,0.198 10 false 32 5.521,0.604 6.135,0.802 0.615,0.198 10 false 31 5.521,1.167 6.135,1.365 0.615,0.198 10 false 24 5.531,1.552 6.146,1.75 0.615,0.198 10 false 22 5.531,2.021 6.146,2.219 0.615,0.198 10 false 23 5.563,2.406 6.177,2.604 0.615,0.198 10 false 9 5.531,2.802 6.146,3 0.615,0.198 10 false 12 5.521,3.208 6.135,3.406 0.615,0.198 10 false 10 5.531,3.594 6.146,3.792 0.615,0.198 10 false 15 5.521,4 6.135,4.198 0.615,0.198 10 false 12 5.531,4.365 6.146,4.563 0.615,0.198 10 false 14 1.146,2.573 2.76,2.948 1.615,0.375 10 false to EFI MAIN NO.1 Relay 1.031,1.75 2.844,2.156 1.813,0.406 10 false from EFI MAIN NO.1 Relay 1.927,1.365 2.813,1.625 0.885,0.26 10 false from Battery 1.667,0.677 2.281,0.875 0.615,0.198 10 false 20 1.677,0.344 2.292,0.542 0.615,0.198 10 false 10 6.021,4.927 6.635,5.125 0.615,0.198 10 false ECM 3.26,1.219 5.073,1.625 1.813,0.406 10 false EFI MAIN NO.1


for 1GR-FE with Automatic Transmission:


C382818E02
0.427,0.99 1.042,1.188 0.615,0.198 10 false G290 0.427,1.156 1.646,1.51 1.219,0.354 10 false No. 6 CAN Junction Connector 5.833,0.323 6.448,0.521 0.615,0.198 10 false CANH 5.823,0.958 6.438,1.156 0.615,0.198 10 false CANL 5.802,1.375 6.417,1.573 0.615,0.198 10 false BATT 5.813,1.771 6.427,1.969 0.615,0.198 10 false +B 5.813,2.177 6.427,2.375 0.615,0.198 10 false +B2 5.813,2.583 6.427,2.781 0.615,0.198 10 false MREL 5.823,2.99 6.438,3.188 0.615,0.198 10 false EC 5.813,3.385 6.427,3.583 0.615,0.198 10 false ME01 5.823,3.76 6.438,3.958 0.615,0.198 10 false E02 5.823,4.167 6.438,4.365 0.615,0.198 10 false E1 5.823,4.563 6.438,4.76 0.615,0.198 10 false E01 5.469,4.563 6.083,4.76 0.615,0.198 10 false C36 5.469,3.771 6.083,3.969 0.615,0.198 10 false C37 5.469,3.375 6.083,3.573 0.615,0.198 10 false C36 5.469,4.167 6.083,4.365 0.615,0.198 10 false C36 5.448,2.979 6.063,3.177 0.615,0.198 10 false G55 5.448,2.583 6.063,2.781 0.615,0.198 10 false G56 5.448,2.188 6.063,2.385 0.615,0.198 10 false G55 5.448,1.771 6.063,1.969 0.615,0.198 10 false G55 5.448,1.365 6.063,1.563 0.615,0.198 10 false G55 5.438,0.802 6.052,1 0.615,0.198 10 false G56 5.448,0.438 6.063,0.635 0.615,0.198 10 false G56 5.51,0.25 6.125,0.448 0.615,0.198 10 false 31 5.521,0.615 6.135,0.813 0.615,0.198 10 false 25 5.521,1.167 6.135,1.365 0.615,0.198 10 false 24 5.531,1.583 6.146,1.781 0.615,0.198 10 false 23 5.531,2.021 6.146,2.219 0.615,0.198 10 false 22 5.531,2.406 6.146,2.604 0.615,0.198 10 false 36 5.531,2.802 6.146,3 0.615,0.198 10 false 3 5.521,3.208 6.135,3.406 0.615,0.198 10 false 29 5.531,3.594 6.146,3.792 0.615,0.198 10 false 14 5.521,4 6.135,4.198 0.615,0.198 10 false 12 5.531,4.365 6.146,4.563 0.615,0.198 10 false 23 1.188,2.573 2.802,2.948 1.615,0.375 10 false to EFI MAIN NO.1 Relay 1.052,1.75 2.865,2.156 1.813,0.406 10 false from EFI MAIN NO.1 Relay 1.917,1.365 2.802,1.625 0.885,0.26 10 false from Battery 1.667,0.677 2.281,0.875 0.615,0.198 10 false 20 1.677,0.344 2.292,0.542 0.615,0.198 10 false 10 6.021,4.927 6.635,5.125 0.615,0.198 10 false ECM 3.208,1.208 5.021,1.615 1.813,0.406 10 false EFI MAIN NO.1


for 1GD-FTV:


C382820E05
0.385,0.958 1,1.156 0.615,0.198 10 false G290 0.385,1.115 1.604,1.521 1.219,0.406 10 false No. 6 CAN Junction Connector 1.667,0.635 2.281,0.833 0.615,0.198 10 false 20 1.677,0.302 2.292,0.5 0.615,0.198 10 false 10 5.406,0.76 6.021,0.958 0.615,0.198 10 false G184 5.406,0.406 6.021,0.604 0.615,0.198 10 false G184 5.406,4.521 6.021,4.719 0.615,0.198 10 false G185 5.406,4.917 6.021,5.115 0.615,0.198 10 false G185 5.406,2.938 6.021,3.135 0.615,0.198 10 false G184 5.417,3.333 6.031,3.531 0.615,0.198 10 false G185 5.802,4.542 6.417,4.74 0.615,0.198 10 false E02 5.833,4.125 6.448,4.323 0.615,0.198 10 false E1 5.813,3.76 6.427,3.958 0.615,0.198 10 false ME01 5.813,3.333 6.427,3.531 0.615,0.198 10 false EC 5.792,2.948 6.406,3.146 0.615,0.198 10 false MREL 5.781,2.563 6.396,2.76 0.615,0.198 10 false +B3 5.813,2.125 6.427,2.323 0.615,0.198 10 false +B2 5.802,1.74 6.417,1.938 0.615,0.198 10 false +B 5.813,0.917 6.427,1.115 0.615,0.198 10 false CANL 5.813,0.323 6.427,0.521 0.615,0.198 10 false CANH 5.51,0.219 6.125,0.417 0.615,0.198 10 false 17 5.521,0.604 6.135,0.802 0.615,0.198 10 false 28 5.531,1.115 6.146,1.313 0.615,0.198 10 false 1 5.531,1.958 6.146,2.156 0.615,0.198 10 false 3 5.813,4.927 6.427,5.125 0.615,0.198 10 false E01 5.542,1.552 6.156,1.75 0.615,0.198 10 false 4 5.406,4.125 6.021,4.323 0.615,0.198 10 false G185 5.802,1.333 6.417,1.531 0.615,0.198 10 false BATT 5.542,2.365 6.156,2.563 0.615,0.198 10 false 2 5.552,3.167 6.167,3.365 0.615,0.198 10 false 8 5.49,2.76 6.104,2.958 0.615,0.198 10 false 14 5.521,3.552 6.135,3.75 0.615,0.198 10 false 1 5.531,3.948 6.146,4.146 0.615,0.198 10 false 5 5.521,4.344 6.135,4.542 0.615,0.198 10 false 3 5.531,4.75 6.146,4.948 0.615,0.198 10 false 4 6.073,5.302 6.688,5.5 0.615,0.198 10 false ECM 1.292,2.927 2.969,3.156 1.677,0.229 10 false to EFI MAIN NO.1 Relay 1.156,1.729 2.854,1.958 1.698,0.229 10 false from EFI MAIN NO.1 Relay 2.021,1.313 3.719,1.542 1.698,0.229 10 false from Battery 3.438,1.156 4.563,1.375 1.125,0.219 10 false EFI MAIN NO.1 5.417,3.729 6.031,3.927 0.615,0.198 10 false G185 5.417,1.344 6.031,1.542 0.615,0.198 10 false G184 5.417,1.74 6.031,1.938 0.615,0.198 10 false G184 5.406,2.125 6.021,2.323 0.615,0.198 10 false G184 5.406,2.542 6.021,2.74 0.615,0.198 10 false G184


for 2TR-FE:


C447923E01
0.427,0.99 1.042,1.188 0.615,0.198 10 false G290 0.427,1.156 1.646,1.51 1.219,0.354 10 false No. 6 CAN Junction Connector 5.833,0.323 6.448,0.521 0.615,0.198 10 false CANH 5.823,0.958 6.438,1.156 0.615,0.198 10 false CANL 5.802,1.385 6.417,1.583 0.615,0.198 10 false BATT 5.813,1.885 6.427,2.083 0.615,0.198 10 false +B 5.813,2.313 6.427,2.51 0.615,0.198 10 false +B2 5.813,2.75 6.427,2.948 0.615,0.198 10 false MREL 5.802,3.26 6.417,3.458 0.615,0.198 10 false ME01 5.823,3.729 6.438,3.927 0.615,0.198 10 false E1 5.823,4.125 6.438,4.323 0.615,0.198 10 false E02 5.823,4.563 6.438,4.76 0.615,0.198 10 false E01 5.406,4.563 6.021,4.76 0.615,0.198 10 false C153 5.417,3.708 6.031,3.906 0.615,0.198 10 false C153 5.406,3.271 6.021,3.469 0.615,0.198 10 false C153 5.417,4.125 6.031,4.323 0.615,0.198 10 false C153 5.417,2.76 6.031,2.958 0.615,0.198 10 false G181 5.406,2.281 6.021,2.479 0.615,0.198 10 false G180 5.406,1.875 6.021,2.073 0.615,0.198 10 false G180 5.406,1.385 6.021,1.583 0.615,0.198 10 false G180 5.406,0.802 6.021,1 0.615,0.198 10 false G181 5.406,0.458 6.021,0.656 0.615,0.198 10 false G181 5.51,0.25 6.125,0.448 0.615,0.198 10 false 13 5.479,0.646 6.094,0.844 0.615,0.198 10 false 14 5.521,1.219 6.135,1.417 0.615,0.198 10 false 3 5.542,1.698 6.156,1.896 0.615,0.198 10 false 1 5.531,2.125 6.146,2.323 0.615,0.198 10 false 2 5.552,2.583 6.167,2.781 0.615,0.198 10 false 6 5.531,3.094 6.146,3.292 0.615,0.198 10 false 4 5.531,3.531 6.146,3.729 0.615,0.198 10 false 3 5.531,3.938 6.146,4.135 0.615,0.198 10 false 2 5.531,4.365 6.146,4.563 0.615,0.198 10 false 1 1.146,2.75 2.76,3.125 1.615,0.375 10 false to EFI MAIN NO.1 Relay 1.031,1.844 2.844,2.25 1.813,0.406 10 false from EFI MAIN NO.1 Relay 1.927,1.365 2.813,1.625 0.885,0.26 10 false from Battery 1.667,0.708 2.281,0.906 0.615,0.198 10 false 20 1.677,0.344 2.292,0.542 0.615,0.198 10 false 10 6.021,4.927 6.635,5.125 0.615,0.198 10 false ECM 3.26,1.219 5.073,1.625 1.813,0.406 10 false EFI MAIN NO.1


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.

C447924C01
1.104,0.333 1.479,0.563 0.375,0.229 3.302,0.375 3.708,0.604 0.406,0.229 5.698,0.354 6.104,0.583 0.406,0.229 0.802,2.51 0.635,2.51 0.635,2.51 0.938,1.813 true 1.208,2.281 1.042,2.281 1.042,2.281 1.156,1.792 true 0.615,0.552 0.802,0.552 0.802,0.552 0.927,1.688 true 3.458,2.104 3.594,2.104 3.594,2.104 3.76,1.417 true 3.563,2.333 3.698,2.333 3.698,2.333 3.885,1.438 true 5.146,2.5 5.281,2.5 5.281,2.5 5.365,1.708 true 5.948,2.302 5.781,2.302 5.781,2.302 5.385,1.563 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.146,0.375 1.458,0.573 0.313,0.198 10 false G56 3.354,0.396 3.76,0.604 0.406,0.208 10 false G181 5.75,0.396 6.156,0.604 0.406,0.208 10 false G184 0.844,2.458 2.063,2.708 1.219,0.25 10 false CANH*C, CANL*B 1.573,0.354 2.135,0.604 0.563,0.25 10 false *A 1.25,2.198 2.448,2.427 1.198,0.229 10 false CANH*B 6.219,0.375 6.781,0.625 0.563,0.25 10 false *D 0.073,0.49 0.635,0.74 0.563,0.25 10 false CANL*C 3.813,0.396 4.375,0.646 0.563,0.25 10 false *E 3.021,2.021 3.583,2.271 0.563,0.25 10 false CANH 3.156,2.281 3.719,2.531 0.563,0.25 10 false CANL 6,2.208 6.563,2.458 0.563,0.25 10 false CANH 4.75,2.427 5.313,2.677 0.563,0.25 10 false CANL
*A for 1GR-FE *B for Manual Transmission
*C for Automatic Transmission *D for 1GD-FTV
*E for 2TR-FE - -
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE with Manual Transmission
Tester Connection Condition Specified Condition
G56-32 (CANH) - G56-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1GR-FE with Automatic Transmission
Tester Connection Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1GD-FTV
Tester Connection Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2TR-FE
Tester Connection Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

for 1GR-FE with Manual Transmission:

i.

Disconnect the ECM connectors.

U148698C01
0.802,0.917 0.625,1.458 0.625,1.458 0.521,1.458 false 5.646,0.885 5.271,0.219 5.271,0.219 5.177,0.219 false 4.115,0.865 4.313,0.74 4.313,0.74 4.406,0.74 false 6.458,0.844 6.656,0.719 6.656,0.719 6.75,0.719 false 6.396,1.25 6.594,1.333 6.594,1.333 6.688,1.333 false 6.156,1.25 6.365,1.531 6.365,1.531 6.469,1.531 false 5.896,1.25 6.031,1.656 6.031,1.656 6.125,1.656 false 3.865,1.073 4.135,1.531 4.135,1.531 4.229,1.531 false 4.104,1.073 4.375,1.302 4.375,1.302 4.479,1.302 false 0.146,0.708 0.438,0.875 0.292,0.167 10 false C36 2.469,0.729 2.76,0.896 0.292,0.167 10 false C37 4.979,0.729 5.271,0.896 0.292,0.167 10 false G55 4.448,0.667 4.833,0.833 0.385,0.167 10 false ME01 0.333,1.385 0.531,1.552 0.198,0.167 10 false E1 0.042,0.01 0.24,0.177 0.198,0.167 10 false *a 4.792,0.156 5.208,0.323 0.417,0.167 10 false MREL 6.792,0.656 7.031,0.823 0.24,0.167 10 false EC 6.698,1.26 7.094,1.427 0.396,0.167 10 false BATT 6.479,1.458 6.875,1.625 0.396,0.167 10 false +B2 6.135,1.583 6.417,1.75 0.281,0.167 10 false +B 4.24,1.458 4.521,1.625 0.281,0.167 10 false E01 4.49,1.229 4.771,1.396 0.281,0.167 10 false E02
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-12 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C37-14 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C37-15 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C37-10 (ME01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G55-12 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



iii.

Reconnect the cable to the negative (-) battery terminal.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G55-24 (BATT) - Body ground Always 11 to 14 V
G55-23 (+B2) - Body ground Battery positive (+) voltage applied to terminal G55-9 (MREL) 11 to 14 V
G55-22 (+B) - Body ground Battery positive (+) voltage applied to terminal G55-9 (MREL) 11 to 14 V




b.

for 1GR-FE and Automatic Transmission:

i.

Disconnect the ECM connectors.

U170542C01
0.74,1.469 0.563,1.646 0.563,1.646 0.469,1.646 false 4.25,0.844 3.823,0.469 3.823,0.469 3.729,0.469 false 4.771,1.375 4.948,1.271 4.948,1.271 5.042,1.271 false 4.531,1.458 4.885,1.688 4.885,1.688 4.979,1.688 false 4.26,1.385 3.708,1.031 3.708,1.031 3.604,1.031 false 2.833,1.313 3.177,1.646 3.177,1.646 3.271,1.646 false 0.729,1.042 0.521,0.896 0.521,0.896 0.427,0.896 false 0.719,1.292 0.51,1.385 0.51,1.385 0.417,1.385 false 6.458,1.427 6.583,1.323 6.583,1.323 6.688,1.323 false 0.979,0.083 1.271,0.25 0.292,0.167 10 false C36 2.479,0.115 2.771,0.281 0.292,0.167 10 false C37 0.042,0.01 0.24,0.177 0.198,0.167 10 false *a 0.083,1.573 0.469,1.74 0.385,0.167 10 false ME01 4.292,0.094 4.583,0.26 0.292,0.167 10 false G55 3.521,0.406 3.76,0.573 0.24,0.167 10 false EC 5.073,1.198 5.469,1.365 0.396,0.167 10 false BATT 5.021,1.604 5.417,1.771 0.396,0.167 10 false +B 3.313,0.958 3.594,1.125 0.281,0.167 10 false +B2 3.281,1.583 3.563,1.75 0.281,0.167 10 false E02 5.979,0.083 6.271,0.25 0.292,0.167 10 false G56 6.698,1.26 7.115,1.427 0.417,0.167 10 false MREL 0.208,0.813 0.594,0.979 0.385,0.167 10 false E1 0.125,1.313 0.51,1.479 0.385,0.167 10 false E01
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-12 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C36-23 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C37-14 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C36-29 (ME01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G55-3 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



iii.

Reconnect the cable to the negative (-) battery terminal.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G55-24 (BATT) - Body ground Always 11 to 14 V
G55-22 (+B2) - Body ground Battery positive (+) voltage applied to terminal G56-36 (MREL) 11 to 14 V
G55-23 (+B) - Body ground Battery positive (+) voltage applied to terminal G56-36 (MREL) 11 to 14 V




c.

for 1GD-FTV:

i.

Disconnect the ECM connectors.

C447925C01
1.667,0.125 2.135,0.375 0.469,0.25 4.969,0.135 5.438,0.385 0.469,0.25 2.021,0.833 2.635,0.479 2.635,0.479 2.865,0.479 true 1.802,0.875 1.021,0.375 1.021,0.375 0.865,0.375 true 1.5,0.906 1,1.167 1,1.167 0.813,1.167 true 1.677,0.948 1.021,1.417 1.021,1.417 0.854,1.417 true 4.708,0.906 4.271,0.615 4.271,0.615 4.063,0.615 true 4.688,1.052 4.302,1.313 4.302,1.313 4.063,1.313 true 5.094,0.833 5.958,0.479 5.958,0.479 6.156,0.479 true 5.385,0.896 5.958,0.677 5.958,0.677 6.156,0.677 true 5.208,0.896 5.927,1.26 5.927,1.26 6.104,1.26 true 2.292,1.073 2.677,0.833 2.677,0.833 2.906,0.833 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.729,0.177 2.354,0.385 0.625,0.208 10 false G184 5.031,0.188 5.656,0.396 0.625,0.208 10 false G185 2.958,0.406 3.427,0.635 0.469,0.229 10 false +B 0.563,0.354 1.031,0.583 0.469,0.229 10 false +B2 0.458,1.063 0.927,1.292 0.469,0.229 10 false BATT 0.552,1.365 1.021,1.594 0.469,0.229 10 false +B3 3.656,0.563 4.125,0.792 0.469,0.229 10 false ME01 3.833,1.229 4.302,1.458 0.469,0.229 10 false EC 6.25,0.438 6.719,0.667 0.469,0.229 10 false E02 6.156,1.219 6.625,1.448 0.469,0.229 10 false E01 6.229,0.635 6.698,0.865 0.469,0.229 10 false E1 2.958,0.771 3.427,1 0.469,0.229 10 false MREL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G185-5 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G185-4 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G185-3 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G185-1 (ME01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G185-8 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



iii.

Reconnect the cable to the negative (-) battery terminal.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G184-1 (BATT) - Body ground Always 11 to 14 V
G184-4 (+B) - Body ground Terminal G184-14 (MREL) connected to body ground 11 to 14 V
G184-3 (+B2) - Body ground Terminal G184-14 (MREL) connected to body ground 11 to 14 V
G184-2 (+B3) - Body ground Terminal G184-14 (MREL) connected to body ground 11 to 14 V




d.

for 2TR-FE:

i.

Disconnect the ECM connectors.

U170540C03
1.51,0.771 1.885,0.292 1.885,0.292 1.99,0.292 true 1.021,0.854 0.823,1.031 0.823,1.031 0.708,1.031 true 3.417,0.771 3.052,0.146 3.052,0.146 2.906,0.146 true 3.271,0.75 2.958,0.49 2.958,0.49 2.865,0.49 true 6.531,0.615 6.354,0.615 6.354,0.615 6.156,0.75 true 2.76,1.167 2.885,1.167 2.885,1.167 3.083,0.854 true 0.708,0.542 0.823,0.542 0.823,0.542 1.198,0.771 true 0.833,0.24 0.938,0.24 0.938,0.24 1.344,0.771 true 0.083,0.052 0.354,0.302 0.271,0.25 10 false *a 3.375,0.135 3.75,0.281 0.375,0.146 10 false G180 5.49,0.135 5.865,0.281 0.375,0.146 10 false G181 1.323,0.135 1.698,0.281 0.375,0.146 10 false C153 6.583,0.552 7.115,0.74 0.531,0.188 10 false MREL 2.531,0.073 2.958,0.219 0.427,0.146 10 false BATT 2.552,1.094 2.979,1.24 0.427,0.146 10 false +B 2.01,0.198 2.438,0.344 0.427,0.146 10 false ME01 0.427,0.958 0.854,1.104 0.427,0.146 10 false E01 2.552,0.417 2.979,0.563 0.427,0.146 10 false +B2 0.438,0.458 0.865,0.604 0.427,0.146 10 false E02 0.625,0.156 1.052,0.302 0.427,0.146 10 false E1
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C153-1 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C153-2 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C153-4 (ME01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



iii.

Reconnect the cable to the negative (-) battery terminal.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G180-3 (BATT) - Body ground Always 11 to 14 V
G180-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G181-6 (MREL) 11 to 14 V
G180-2 (+B2) - Body ground Battery positive (+) voltage applied to terminal G181-6 (MREL) 11 to 14 V





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)