There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
·
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher. ·
Resistance between terminals 19 (CAYH) and 20 (CAYL) of the central gateway ECU (network gateway ECU) is 70 Ω or higher. |
·
CAN main bus lines or connector ·
Central gateway ECU (network gateway ECU) ·
No. 5 CAN junction connector |
This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from negative (-) battery terminal.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Central Gateway ECU (Network Gateway ECU) |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G289-1 (CANH) - G289-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| G289-2 (CANH) - G289-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G229 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-6 (CA3H) - G289-1 | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G229-21 (CA3L) - G289-12 | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G229-19 (CAYH) - G289-2 | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G229-20 (CAYL) - G289-13 | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG