There may be a short circuit between one of the CAN bus wires and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Navigation System *2: w/ Audio and Visual System (for Radio and Display Type) *3: w/ Telematics Transceiver |
|
·
No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. ·
No resistance exists between terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. |
·
Short to GND in CAN main bus line ·
Short to GND in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Radio and display receiver assembly (EMVN ECU)*1, *2 ·
Telematics transceiver*3 ·
No. 5 CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from negative (-) battery terminal.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) |
| *d | to Central Gateway ECU (Network Gateway ECU) |
| *e | to Radio and Display Receiver Assembly (EMVN ECU) (w/ Audio and Visual System (for Radio and Display Type), w/ Navigation System) |
| *f | to Telematics Transceiver (w/ Telematics Transceiver) |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Navigation System *2: w/ Audio and Visual System (for Radio and Display Type) *3: w/ Telematics Transceiver |
|||
| G289-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| G289-12 (CANL) - G317-4 (CG) | |||
| G289-2 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| G289-13 (CANL) - G317-4 (CG) | |||
| G289-3 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Radio and display receiver assembly (EMVN ECU)*1, *2 |
| G289-14 (CANL) - G317-4 (CG) | |||
| G289-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Telematics transceiver*3 |
| G289-15 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Reconnect the G289 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-6 (CA3H) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-21 (CA3L) - G317-4 (CG) | ||
| G229-19 (CAYH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-20 (CAYL) - G317-4 (CG) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connectors.
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short to GND is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-6 (CA3H) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-21 (CA3L) - G317-4 (CG) |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.
| Proceed to |
|---|
| OK |
| NG |
OK
NG