There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Multi-terrain Monitor System *2: w/ Pre-collision System *3: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display) *4: w/ Kinetic Dynamic Suspension System *5: w/ Air Suspension System *6: w/ Blind Spot Monitor System |
|
| There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. | ·
Short to GND in CAN main bus line ·
Short to GND in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Parking assist ECU*1 ·
4 wheel drive control ECU (4WD control ECU) ·
Clearance warning ECU assembly*3 ·
Stabilizer control ECU*4 ·
Forward recognition camera*2 ·
Blind spot monitor sensor LH*6 ·
Millimeter wave radar sensor assembly*2 ·
Suspension control ECU*5 ·
No. 1 CAN junction terminal ·
No. 1 CAN junction connector ·
No. 3 CAN junction connector ·
No. 7 CAN junction connector |
for LHD:
for RHD:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 7 CAN Junction Connector | *d | to Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) |
| *e | to Forward Recognition Camera (w/ Pre-collision System) | *f | to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) |
| *g | to No. 1 CAN Junction Connector | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Kinetic Dynamic Suspension System *2: w/ Pre-collision System *3: w/ Blind Spot Monitor System |
|||
| G287-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 7 CAN junction connector |
| G287-11 (CANL) - G317-4 (CG) | |||
| G287-2 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Stabilizer control ECU*1 |
| G287-12 (CANL) - G317-4 (CG) | |||
| G287-3 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Forward recognition camera*2 |
| G287-13 (CANL) - G317-4 (CG) | |||
| G287-9 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Blind spot monitor sensor LH*3 |
| G287-19 (CANL) - G317-4 (CG) | |||
| G287-10 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction connector |
| G287-20 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 7 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G287 No. 3 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Suspension Control ECU (w/ Air Suspension System) |
| *d | to Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System) |
| *e | to No. 1 CAN Junction Terminal |
| *f | to No. 3 CAN Junction Connector |
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Air Suspension System *2: w/ Pre-collision System |
|||
| A121-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Suspension control ECU*1 |
| A121-7 (CANL) - G317-4 (CG) | |||
| A121-2 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Millimeter wave radar sensor assembly*2 |
| A121-8 (CANL) - G317-4 (CG) | |||
| A121-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction terminal |
| A121-10 (CANL) - G317-4 (CG) | |||
| A121-5 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 3 CAN junction connector |
| A121-11 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Reconnect the G287 No. 3 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 7 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 3 CAN Junction Connector | *d | to Central Gateway ECU (Network Gateway ECU) |
| *e | to Parking Assist ECU (w/ Multi-terrain Monitor System) | *f | to 4 Wheel Drive Control ECU (4WD Control ECU) |
| *g | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [w/ Multi-display]) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Parking Assist Monitor System *2: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display) |
|||
| G291-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 3 CAN junction connector |
| G291-11 (CANL) - G317-4 (CG) | |||
| G291-2 (CANH)- G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| G291-12 (CANL) - G317-4 (CG) | |||
| G291-3 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Parking assist ECU*1 |
| G291-13 (CANL) - G317-4 (CG) | |||
| G291-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4 wheel drive control ECU (4WD control ECU) |
| G291-14 (CANL) - G317-4 (CG) | |||
| G291-5 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Clearance warning ECU assembly*2 |
| G291-15 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G291 No. 7 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-15 (CA5H) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-16 (CA5L) - G317-4 (CG) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 7 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 3 CAN Junction Connector | *d | to No. 1 CAN Junction Connector |
| *e | to 4 Wheel Drive Control ECU (4WD Control ECU) | *f | to Forward Recognition Camera (w/ Pre-collision System) |
| *g | to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) | *h | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type with Multi-display]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ Blind Spot Monitor System *3: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type with Multi-display) |
|||
| G291-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 3 CAN junction connector |
| G291-11 (CANL) - G317-4 (CG) | |||
| G291-3 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction connector |
| G291-13 (CANL) - G317-4 (CG) | |||
| G291-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4 wheel drive control ECU (4WD control ECU) |
| G291-14 (CANL) - G317-4 (CG) | |||
| G291-5 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Forward recognition camera*1 |
| G291-15 (CANL) - G317-4 (CG) | |||
| G291-6 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Blind spot monitor sensor LH*2 |
| G291-16 (CANL) - G317-4 (CG) | |||
| G291-7 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Clearance warning ECU assembly*3 |
| G291-17 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 3 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G291 No. 7 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Suspension Control ECU (w/ Air Suspension System) |
| *d | to Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System) |
| *e | to No. 7 CAN Junction Connector |
| *f | to Central Gateway ECU (Network Gateway ECU) |
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Air Suspension System *2: w/ Pre-collision System |
|||
| A121-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Suspension control ECU*1 |
| A121-7 (CANL) - G317-4 (CG) | |||
| A121-2 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Millimeter wave radar sensor assembly*2 |
| A121-8 (CANL) - G317-4 (CG) | |||
| A121-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 7 CAN junction connector |
| A121-10 (CANL) - G317-4 (CG) | |||
| A121-5 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| A121-11 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | B |
| NG (No. 7 CAN junction terminal CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the A121 No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-15 (CA5H) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-16 (CA5L) - G317-4 (CG) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G291 No. 7 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 7 CAN Junction Connector | *d | to Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) |
| *e | to Parking Assist ECU (w/ Multi-terrain Monitor System) | *f | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type with Multi-display]) |
| *g | to No. 1 CAN Junction Terminal | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Kinetic Dynamic Suspension System *2: w/ Multi-terrain Monitor System *3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type with Multi-display) |
|||
| G287-1 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 7 CAN junction connector |
| G287-11 (CANL) - G317-4 (CG) | |||
| G287-2 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Stabilizer control ECU*1 |
| G287-12 (CANL) - G317-4 (CG) | |||
| G287-4 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Parking assist ECU*2 |
| G287-14 (CANL) - G317-4 (CG) | |||
| G287-5 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Clearance warning ECU assembly*3 |
| G287-15 (CANL) - G317-4 (CG) | |||
| G287-10 (CANH) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction terminal |
| G287-20 (CANL) - G317-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 7 CAN junction connector CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Reconnect the wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-15 (CA5H) - G317-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G229-16 (CA5L) - G317-4 (CG) |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.
| Proceed to |
|---|
| OK |
| NG |
OK
NG