Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
Engine Stop and Start ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table".

Click here(Click here)


·

Engine stop and start ECU CAN branch wire or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C369184E06
0.219,1.344 0.833,1.542 0.615,0.198 10 false G286 0.229,1.542 2.333,1.802 2.104,0.26 10 false No. 2 CAN Junction Connector 1.719,0.458 2.031,0.656 0.313,0.198 10 false 5 1.698,1.021 2.01,1.219 0.313,0.198 10 false 15 5.219,0.573 5.833,0.771 0.615,0.198 10 false G314 5.219,1.729 5.677,1.927 0.458,0.198 10 false G312 5.219,1.125 5.833,1.323 0.615,0.198 10 false G314 5.219,2.375 5.833,2.573 0.615,0.198 10 false G314 5.219,3 5.833,3.198 0.615,0.198 10 false G314 5.219,3.667 5.833,3.865 0.615,0.198 10 false G314 5.219,4.396 5.677,4.594 0.458,0.198 10 false G312 5.302,0.354 5.615,0.552 0.313,0.198 10 false 13 5.302,0.917 5.583,1.135 0.281,0.219 10 false 14 5.333,1.521 5.49,1.719 0.156,0.198 10 false 3 5.302,2.156 5.615,2.354 0.313,0.198 10 false 21 5.292,2.771 5.604,2.969 0.313,0.198 10 false 18 5.292,3.448 5.604,3.646 0.313,0.198 10 false 19 5.333,4.198 5.49,4.396 0.156,0.198 10 false 8 5.146,5.313 7.042,5.552 1.896,0.24 10 false Engine Stop and Start ECU 5.625,0.573 6.24,0.771 0.615,0.198 10 false CANH 5.625,1.125 6.24,1.323 0.615,0.198 10 false CANL 5.635,1.729 6.25,1.927 0.615,0.198 10 false BIN1 5.646,2.365 6.104,2.563 0.458,0.198 10 false IG1 5.646,3 6.104,3.198 0.458,0.198 10 false IG2 5.635,3.667 6.094,3.865 0.458,0.198 10 false ACC 5.646,4.396 6.26,4.594 0.615,0.198 10 false GND1 4.146,1.542 5.521,1.74 1.375,0.198 10 false BBC NO. 2 4.073,2.208 5.188,2.438 1.115,0.229 10 false ECU-IG NO.1 4.229,2.833 5.031,3.094 0.802,0.26 10 false S&S IG2 4.333,3.49 5.063,3.75 0.729,0.26 10 false ACC 2.438,2.99 3.698,3.479 1.26,0.49 10 false from IG2 Relay 2.417,3.656 3.656,3.938 1.24,0.281 10 false from ACC Relay 2.646,1.698 4.479,1.896 1.833,0.198 10 false from Battery 2.219,2.354 3.635,2.708 1.417,0.354 10 false from IG NO.1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C298836C38
1.563,0.104 1.979,0.396 0.417,0.292 0.75,1.458 0.521,1.854 true 0.885,1.448 1.188,1.833 true 1.604,0.177 2.156,0.427 0.552,0.25 10 false G314 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 1.104,1.885 1.719,2.083 0.615,0.198 10 false CANL 0.281,1.896 0.896,2.094 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G314-13 (CANH) - G314-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C323601C49
1.531,0.177 1.958,0.448 0.427,0.271 1.531,2.052 1.958,2.323 0.427,0.271 0.646,1.604 1.146,1.354 true 1.76,4.063 1.542,3.51 true 0.885,4.083 1.385,3.51 true 2.51,4.031 2.167,3.5 true 2.833,1.625 2.417,1.396 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.573,0.24 2.031,0.438 0.458,0.198 10 false G312 0.323,1.552 0.781,1.75 0.458,0.198 10 false BIN1 1.594,2.115 2.323,2.542 0.729,0.427 10 false G314 1.646,4.115 2.104,4.313 0.458,0.198 10 false ACC 0.792,4.125 1.25,4.323 0.458,0.198 10 false IG2 2.458,4.073 2.917,4.271 0.458,0.198 10 false IG1 2.885,1.583 3.354,1.75 0.469,0.167 10 false GND1
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G312-8 (GND1) -Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G312-3 (BIN1) - Body ground Always 11 to 14 V
G314-19 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G314-21 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G314-18 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)