Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C217558E06
5.813,2.844 6.281,3.021 0.469,0.177 10 false GND1 5.385,3.802 5.781,3.979 0.396,0.177 10 false A6 5.385,3.958 7.01,4.323 1.625,0.365 10 false Brake Actuator Assembly (Skid Control ECU) 0.521,1.521 1.01,1.74 0.49,0.219 10 false A119 0.521,1.677 2.563,2.24 2.042,0.563 10 false No. 1 CAN Junction Connector 5.813,0.667 6.281,0.844 0.469,0.177 10 false CANH 1.938,0.573 2.219,0.729 0.281,0.156 10 false 11 5.531,1.021 5.729,1.177 0.198,0.156 10 false 14 5.531,0.573 5.729,0.729 0.198,0.156 10 false 25 5.531,1.885 5.729,2.042 0.198,0.156 10 false 12 5.813,1.979 6.281,2.156 0.469,0.177 10 false +BS 5.531,1.469 5.729,1.625 0.198,0.156 10 false 24 4.75,1.427 5.458,1.583 0.708,0.156 10 false ABS NO.1 4.75,1.844 5.458,2 0.708,0.156 10 false ABS NO.2 2.917,1.594 3.906,1.917 0.99,0.323 10 false from Battery 2.823,2.396 4.302,2.646 1.479,0.25 10 false from IG1 NO.1 Relay 4.604,2.219 5.51,2.375 0.906,0.156 10 false ECU-IG NO.1 5.531,2.271 5.719,2.427 0.188,0.156 10 false 34 5.573,2.74 5.729,2.896 0.156,0.156 10 false 1 5.531,3.156 5.729,3.313 0.198,0.156 10 false 13 1.938,1.021 2.25,1.219 0.313,0.198 10 false 22 5.813,1.104 6.281,1.281 0.469,0.177 10 false CANL 5.813,1.552 6.281,1.729 0.469,0.177 10 false BM 5.813,2.375 6.281,2.552 0.469,0.177 10 false IG1 5.813,3.25 6.281,3.427 0.469,0.177 10 false GND2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U148256C01
1.313,1.344 1.042,1.948 1.042,1.948 0.938,1.948 true 1.313,1.219 0.802,1.75 0.802,1.75 0.719,1.75 true 0.115,0.031 0.313,0.229 0.198,0.198 10 false *a 1.688,0.125 1.969,0.313 0.281,0.188 10 false A6 0.323,1.656 0.844,1.854 0.521,0.198 10 false CANL 0.5,1.865 1.083,2.063 0.583,0.198 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U148964C01
2.469,0.844 2.854,0.146 2.854,0.146 2.99,0.146 false 2.313,1.396 2.583,1.917 2.583,1.917 2.76,1.917 false 1.115,0.844 0.708,0.354 0.708,0.354 0.573,0.354 false 1.115,1.323 0.781,1.802 0.781,1.802 0.604,1.802 false 2.469,1.135 2.927,0.521 2.927,0.521 3.073,0.521 false 0.083,0.271 0.542,0.417 0.458,0.146 10 false GND1 0.083,1.708 0.542,1.854 0.458,0.146 10 false GND2 3.01,0.073 3.323,0.219 0.313,0.146 10 false +BS 3.094,0.448 3.354,0.594 0.26,0.146 10 false BM 2.781,1.833 3.24,1.979 0.458,0.146 10 false IG1 1.698,0.125 2.01,0.313 0.313,0.188 10 false A6 0.083,0.01 0.542,0.156 0.458,0.146 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A6-13 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-12 (+BS) - Body ground Always 11 to 14 V
A6-24 (BM) - Body ground Always 11 to 14 V
A6-34 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)