The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P256212 | Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High Circuit Short to Battery | VNA voltage is 4.9 V or higher for 2.1 seconds.
(1 trip detection logic) |
·
Nozzle vane position sensor (turbocharger nozzle vane control actuator) ·
Open or short in nozzle vane position sensor circuit ·
ECM |
Comes on | DTC stored | SAE Code: P2565 |
| P256214 | Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low Circuit Short to Ground or Open | VNA voltage is 0.1 V or less for 2.1 seconds.
(1 trip detection logic) |
·
Nozzle vane position sensor (turbocharger nozzle vane control actuator) ·
Open or short in nozzle vane position sensor circuit ·
ECM |
Comes on | DTC stored | SAE Code: P2564 |
If DTC P256212 and/or P256214 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
- Lack of power
- Vehicle surge or hesitation under light or medium load
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P256212
P256214 |
Ignition switch ON for 2 seconds or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Nozzle Vane Position Sensor) |
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C144-1 (VNVC) - C144-2 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-23 (VNA) - C151-22 (VNE2) | Ignition switch ON | 2.3 to 2.7 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C144-3 (VTA1) - C151-23 (VNA) | Always | Below 1 Ω |
| C144-2 (VNE2) - C151-22 (VNE2) | Always | Below 1 Ω |
| C144-3 (VTA1) or C151-23 (VNA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C144-2 (VNE2) or C151-22 (VNE2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the nozzle vane position sensor connector.
| *a | Front view of wire harness connector
(to Nozzle Vane Position Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C144-1 (VNVC) - C144-3 (VTA1) | Ignition switch off | No short or no open circuit |
| C144-3 (VTA1) - C144-2 (VNE2) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the turbocharger nozzle vane control actuator.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-30 (VNVC) - C151-22 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 2 seconds or more.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P256212 and/or P256214.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, idle the engine.
| Proceed to |
|---|
| NEXT |
NEXT