Home › Engine / Hybrid System › 5L-E (FUEL) › FUEL INJECTION NOZZLE › from 2020.08
RM27T0E _51 Engine / Hybrid System _053668 5L-E FUEL _0260559 FUEL INJECTION NOZZLE A

5L-E FUEL  FUEL INJECTION NOZZLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the injection nozzle removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 26100 3.REMOVE DIESEL THROTTLE BODY

a.

Hide 4.REMOVE INJECTION PIPE SET

a.
A121940E04
1.146,1.167 0.656,0.865 0.656,0.865 0.573,0.865 true 1.344,3.854 1.01,4.365 1.01,4.365 0.938,4.365 true 0.385,0.771 0.625,1 0.24,0.229 10 false *1 0.052,0.042 0.313,0.281 0.26,0.24 10 false *a 0.042,2.281 0.292,2.51 0.25,0.229 10 false *b 0.729,4.271 0.948,4.49 0.219,0.219 10 false *1

Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

Text in Illustration
*1 Union Nut Wrench
*a for Injection Nozzle Side
*b for Injection Pump Side


b.

Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with 2 lower pipe clamps.


Hide 19871 5.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 23760 6.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A121941

Disconnect the fuel hose from the leakage pipe.


b.

Remove the 4 nuts, leakage pipe and 4 ring packing washers.


Hide 23600 7.REMOVE NOZZLE HOLDER AND NOZZLE SET

a.
A121942E03
1.385,1.208 2.667,1.771 true 2.719,1.688 3.156,1.938 0.438,0.25 10 true SST

Using SST, remove the 4 injection nozzles, 4 injection nozzle seats and 4 injection nozzle seat gaskets.

SST
09268-64010  (09268-64020)