Home › Engine / Hybrid System › 2TR-FE (FUEL) › FUEL INJECTOR › from 2020.08
RM27T0E _51 Engine / Hybrid System _053666 2TR-FE FUEL _0260541 FUEL INJECTOR A

2TR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel injector assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 22030 4.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 23271F 5.DISCONNECT FUEL HOSE

A355175

a.

Hide 23273C 6.DISCONNECT NO. 2 FUEL HOSE

A355176

a.

Slide the clamp and disconnect the No. 2 fuel hose.


Hide 23270 7.REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

Hide 23814B 8.REMOVE FUEL DELIVERY PIPE WITH FUEL INJECTOR

A355177

a.

Disconnect the 4 fuel injector assembly connectors.


b.

Disconnect the purge VSV connector.


c.

Detach the wire harness clamp.


d.

Remove the bolt and disconnect the wire harness clamp bracket.


e.
A355178

Remove the bolt and disconnect the purge VSV.


f.
A347971

Remove the 2 bolts and fuel delivery pipe together with the fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



g.
A355179E03
0.552,0.583 0.552,0.823 false 0.469,0.833 0.656,1.021 0.188,0.188 10 false *a

Remove the 2 No. 1 delivery pipe spacers.

Text in Illustration
*a Protective Tape


h.

Remove the 4 injector vibration insulators.


i.

Using a screwdriver, remove the 4 spacers.

HINT:

Tape the screwdriver tip before use.



Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

a.
A355180

Remove the 4 fuel injector assemblies from the fuel delivery pipe.

Text in Illustration
V100135

Pull Out


b.
A348623E01
3.11,0.94 3.336,1.133 0.225,0.193 10 *a 2.655,1.319 2.872,1.021 2.872,1.021 3.073,1.021 false

Remove the 4 O-rings from the 4 fuel injector assemblies.

Text in Illustration
*a O-ring