Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter assembly receives a text data signal from the radio and display receiver assembly (for Radio and Display Type) via local bus communication.

Based on this signal, audio and visual system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC Code DTC Detection Condition Trouble Area
B150A Both conditions are met:
After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly (for Radio and Display Type) when the ignition switch ACC, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.
·

Harness or connector

·

radio and display receiver assembly (for Radio and Display Type)

·

Combination meter assembly



WIRING DIAGRAM

E295995E90
5.177,2.698 7.156,2.927 1.979,0.229 10 false G304 5.188,2.854 7.021,3.25 1.833,0.396 10 false Combination Meter Assembly 5.375,1.802 6.5,2.104 1.125,0.302 10 false MSCL 5.375,1.125 6.5,1.427 1.125,0.302 10 false MSCH 5.094,1.677 6.219,1.979 1.125,0.302 10 false 37 5.083,1.01 6.208,1.313 1.125,0.302 10 false 38 1.125,3.396 2.885,3.708 1.76,0.313 10 false : CAN Communication Line 0.604,2.698 2.323,3.01 1.719,0.313 10 false H93 0.604,2.854 3.323,3.094 2.719,0.24 10 false Radio and Display Receiver Assembly 1.427,1.135 1.979,1.521 0.552,0.385 10 false CNH1 1.938,1 3.063,1.302 1.125,0.302 10 false 5 1.948,1.656 3.073,1.958 1.125,0.302 10 false 6 1.417,1.844 1.969,2.229 0.552,0.385 10 false CNL1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK FOR DTC (NAVIGATION SYSTEM)

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G304 combination meter assembly connector.


b.

Disconnect the H93 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-38(MSCH) - H93-5(CNH1) Always Below 1 Ω
G304-37(MSCL) - H93-6(CNL1) Always Below 1 Ω
G304-38(MSCH) or H93-5(CNH1) - Body ground Always 10 kΩ or higher
G304-37(MSCL) or H93-6(CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the ignition switch to ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver.(for Radio and Display Type)



c.
E309521C02
1.813,0.698 1.979,0.354 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 2.063,0.281 2.375,0.438 0.313,0.156 10 false *b
*a Multi-information Display
*b Audio Tab


Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

OK:

The audio tab illuminates and DTC B150A is not output.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG