This DTC is stored if the parking assist ECU judges that there is an internal malfunction as a result of its self check.
The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1611 | ·
ROM/SUM check status malfunction ·
Mirror storage signal malfunction ·
EEPROM status (Initial read) malfunction ·
RAM check status malfunction ·
CPU communication malfunction ·
Video output malfunction |
·
Parking assist ECU initialization (not initialized parking assist ECU) ·
Back camera position setting (initialized parking assist ECU) ·
Side camera position setting (initialized parking assist ECU) ·
Steering Angle setting (initialized parking assist ECU) ·
Parking assist ECU |
When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).
Read the Data List according to the display on the GTS (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Video Output Status | Status of the video output status / OK or NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
| ROM/SUM Check | Status of the ROM/SUM check / OK or NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
| EEPROM Status (Initial read) | Status of the EEPROM check (initial read) / OK or NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
| RAM Check | Status of the RAM check / OK or NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
| CPU Communication Status | Continuous bus off / Not detected or detected | Not detected: Communication condition available
Detected: Communication condition not available |
- |
| Mirror Storage Signal | Status of the mirror storage signal / NG or OK | NG: Status of the mirror storage signal is abnormal
OK: Status of the mirror storage signal is normal |
- |
| Result | Proceed to |
|---|---|
| OK is displayed for all items. | A |
| NG is displayed except EEPROM Status (Initial read). | A |
| NG is displayed for Video Output Status | B |
A
B
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.
If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.
Use the transition of diagnosis screens (note which transition pattern occurs) to confirm if the parking assist ECU was able to properly store the information from initialization (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DIAGNOSIS SYSTEM).
The procedure to make the parking assist ECU store the vehicle information differs when the parking assist ECU has stored the information (initialized) and when the information has not been stored (not initialized).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
DTC C1611 is not output.
If DTC C1611 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.
If DTC C1611 is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.
If DTC C1611 is output frequently, replace the parking assist ECU even though the DTC is not output when rechecking for DTCs.
OK
NG
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL