Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1613  ACC Voltage is Low or High  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that the voltage received by terminal ACC is not normal.

DTC Code DTC Detection Condition Trouble Area
C1613
·

ACC voltage is low

·

ACC voltage is high


·

Harness or connector

·

Parking assist ECU



WIRING DIAGRAM

E456216E02
1.25,0.885 2.385,1.146 1.135,0.26 10 false from ACC Relay 3.208,1.094 4.01,1.375 0.802,0.281 10 false ACC 4.917,0.885 5.448,1.177 0.531,0.292 10 false ACC 4.896,1.438 5.427,1.708 0.531,0.271 10 false GND1 4.76,2 5.292,2.271 0.531,0.271 10 false I6 4.76,2.229 6.208,2.521 1.448,0.292 10 false Parking Assist ECU 4.698,1.365 4.938,1.542 0.24,0.177 10 false 4 4.698,0.75 4.958,0.99 0.26,0.24 10 false 9 0.26,0.51 2.51,0.823 2.25,0.313 10 false from Engine Stop and Start ECU 3.99,0.333 4.25,0.573 0.26,0.24 10 false *1 4,0.76 4.26,1 0.26,0.24 10 false *2 0.073,2.083 2.323,2.396 2.25,0.313 10 false *1: w/ Stop and Start System 0.083,2.406 2.333,2.719 2.25,0.313 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

DTC C1613 is not output.


HINT:

If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.




OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U166298E03
2.5,0.969 2.667,0.531 2.667,0.531 2.865,0.531 true 1.427,1.323 1.229,1.781 1.229,1.781 1.021,1.781 true 1.625,0.333 1.979,0.552 0.354,0.219 10 false I6 2.938,0.458 3.375,0.677 0.438,0.219 10 false GND1 0.688,1.708 1.104,1.938 0.417,0.229 10 false ACC 0.083,0.052 0.333,0.24 0.25,0.188 10 false *a

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

I6-9 (ACC) - I6-4 (GND1) Engine switch on (ACC) 11 to 14 V*1
10.5 to 16 V*2
I6-9 (ACC) - I6-4 (GND1) Engine switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR