Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  


DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of ifs self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1681 Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E377922E02
1.219,0.625 1.833,0.823 0.615,0.198 10 false BCB+ 1.219,1.104 1.833,1.302 0.615,0.198 10 false BCV+ 1.24,1.594 1.854,1.792 0.615,0.198 10 false BCV- 1.229,2.083 1.844,2.281 0.615,0.198 10 false BGND 1.688,0.521 1.844,0.719 0.156,0.198 10 false 6 1.688,0.979 1.844,1.177 0.156,0.198 10 false 3 1.688,1.469 1.844,1.667 0.156,0.198 10 false 2 1.688,1.958 1.844,2.156 0.156,0.198 10 false 5 0.396,2.906 1.01,3.104 0.615,0.198 10 false g1 0.406,3.104 2.781,3.344 2.375,0.24 10 false Front Television Camera Assembly 5.177,0.531 5.438,0.708 0.26,0.177 10 false 11 5.188,1 5.448,1.177 0.26,0.177 10 false 12 5.188,1.5 5.448,1.677 0.26,0.177 10 false 36 5.188,2 5.448,2.177 0.26,0.177 10 false 35 5.51,0.604 6.125,0.802 0.615,0.198 10 false BCB+ 5.521,1.094 6.135,1.292 0.615,0.198 10 false BCV+ 5.521,1.594 6.135,1.792 0.615,0.198 10 false BCV- 5.531,2.083 6.146,2.281 0.615,0.198 10 false BGND 5.448,2.906 6.063,3.104 0.615,0.198 10 false I7 5.448,3.083 6.896,3.385 1.448,0.302 10 false Parking Assist ECU 3.521,2.219 3.667,2.448 0.146,0.229 10 false * 0.406,3.469 1.385,3.656 0.979,0.188 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as multi-terrain monitor system may be needed (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the g1 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-36 (BCV-) - g1-2 (BCV-) Always Below 1 Ω
I7-12 (BCV+) - g1-3 (BCV+) Always Below 1 Ω
I7-35 (BGND) - g1-5 (BGND) Always Below 1 Ω
I7-11 (BCB+) - g1-6 (BCB+) Always Below 1 Ω
I7-36 (BCV-) - Body ground Always 10 kΩ or higher
I7-12 (BCV+) - Body ground Always 10 kΩ or higher
I7-35 (BGND) - Body ground Always 10 kΩ or higher
I7-11 (BCB+) - Body ground Always 10 kΩ or higher




OK

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.
E330226C09
1.469,0.583 1.854,0.771 0.385,0.188 1.229,1.156 1.042,1.781 1.042,1.781 0.969,1.781 true 1.302,1.156 1.5,1.781 1.5,1.781 1.573,1.781 true 1.646,1.688 2.115,1.948 0.469,0.26 10 false BGND 0.146,0.104 0.615,0.365 0.469,0.26 10 false *a 0.51,1.677 0.979,1.938 0.469,0.26 10 false BCV- 1.604,0.594 1.917,0.792 0.313,0.198 10 false I7
*a Component without harness connected
(Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
35 (BGND) - Body ground Always Below 1 Ω
36 (BCV-) - Body ground Always Below 1 Ω




OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

3.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
U166331C01
1.302,1.156 1.385,1.438 1.385,1.438 1.563,1.438 true 1.333,0.979 1.219,0.677 1.219,0.677 1.052,0.677 true 0.104,0.094 0.333,0.354 0.229,0.26 10 false *a 0.625,0.594 1.094,0.833 0.469,0.24 10 false BCB+ 1.583,0.542 2.073,0.771 0.49,0.229 10 false I7 1.615,1.354 2.094,1.573 0.479,0.219 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Disconnect the front television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I7-11 (BCB+) - I7-35 (BGND) Engine switch on (IG) 5.5 to 7.05 V
I7-11 (BCB+) - I7-35 (BGND) Engine switch off Below 1 V




OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Check the waveform of the front television camera assembly using an oscilloscope.

E349797E10
0.823,0.646 1.156,0.823 0.333,0.177 0.677,0.979 0.646,0.75 0.646,0.75 0.531,0.75 true 0.938,1.365 0.76,1.365 0.76,1.365 0.698,1.115 true 3.823,2.292 3.688,2.292 3.688,2.292 3.615,1.604 true 4.26,1.99 4.052,1.99 4.052,1.99 3.719,1.552 true 6.271,2.24 6.063,2.24 6.063,2.24 5.958,1.458 true 6.656,2.021 6.448,2.021 6.448,2.021 6.073,1.406 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 3.094,0.125 3.406,0.323 0.313,0.198 10 false *b 5.344,0.115 5.656,0.313 0.313,0.198 10 false *c 0.115,0.667 0.677,0.885 0.563,0.219 10 false BCV+ 1.01,1.281 1.573,1.5 0.563,0.219 10 false BGND 0.948,0.656 1.323,0.833 0.375,0.177 10 false I7 2.833,1.073 3.25,1.292 0.417,0.219 10 false GND 5.115,1.063 5.531,1.281 0.417,0.219 10 false GND 3.865,2.208 4.177,2.406 0.313,0.198 10 false *d 4.323,1.917 4.635,2.115 0.313,0.198 10 false *e 6.708,1.938 7.021,2.135 0.313,0.198 10 false *e 6.292,2.125 6.604,2.323 0.313,0.198 10 false *d

Text in Illustration
*a Component with harness connected
(Parking Assist ECU)
*b Waveform A
*c Waveform B *d Synchronization Signal
*e Video Waveform - -

HINT:

The video waveform changes according to the image sent by the front television camera assembly.


Item Content
Terminal No. (Symbol) I7-12 (BCV+) - I7-35 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition
·

Waveform A: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is not covered, displaying an image

·

Waveform B: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is covered, blacking out the screen



OK:

Waveform is as shown in the illustration.




OK

NG