Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.08
RM27T0E _51 Engine / Hybrid System _053678 1GR-FE INTAKE / EXHAUST _0260642 INTAKE MANIFOLD A

1GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel pressure regulator assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 11259 7.REMOVE V-BANK COVER

a.
A229925E01
3.107,0.606 3.274,0.769 0.167,0.162 10 *1 1.136,0.536 1.304,0.699 0.167,0.162 10 *2 1.107,0.626 1.028,0.626 false 1.028,0.623 0.942,0.817 false 2.751,0.695 3.083,0.695 false

Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

Text in Illustration
*1 Pin
*2 Hook


Hide 17881 8.REMOVE NO. 1 AIR CLEANER HOSE

a.
A221455

Disconnect the ventilation hose and vacuum hose.


b.

Detach the wire harness clamp.


c.

Remove the bolt and loosen the 2 hose clamps.


d.

Remove the No. 1 air cleaner hose.


Hide 17360 9.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

a.
A221459

for Bank 1 Side:

Remove the bolt and disconnect the air tube assembly from the emission control valve set.


b.
A221458

for Bank 2 Side:

Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.


Hide 17129 10.REMOVE INTAKE AIR SURGE TANK

a.
A221456

Disconnect the throttle body connector.


b.

Disconnect the No. 4 water by-pass hose.


c.

Disconnect the No. 5 water by-pass hose.


d.
A221457

Disconnect the No. 1 fuel vapor feed hose.


e.

Disconnect the No. 1 vacuum switching valve connector.


f.

Disconnect the No. 1 ventilation hose.


g.
A221464

Detach the 2 heater hose clamps.


h.
A221460

Remove the 2 bolts and throttle body bracket.


i.
A221461

Using a clip remover, detach the wire harness clamp.


j.
A221462

Remove the 2 bolts and No. 1 surge tank stay.


k.
A221463

Remove the 2 bolts and No. 2 surge tank stay.


l.
A221465

Remove the 2 nuts, 4 bolts and intake air surge tank.


m.

Remove the gasket.


Hide 23807 11.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 17111 12.REMOVE INTAKE MANIFOLD

a.
A221466

Remove the 4 nuts, 6 bolts and 2 gaskets.