Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.08
RM27T0E _51 Engine / Hybrid System _053678 1GR-FE INTAKE / EXHAUST _0260642 INTAKE MANIFOLD A

1GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A221467

Set a new gasket on each cylinder head.

NOTICE:
·

Align the port holes of the gasket and cylinder head.

·

Be careful of the installation direction.




b.

Set the intake manifold on the cylinder heads.


c.
A221466E03
0.344,1.74 0.635,1.948 0.292,0.208 10 true *1 0.073,0.302 0.313,0.51 0.24,0.208 10 true *1 3.125,0.281 3.385,0.51 0.26,0.229 10 true *1 3.073,1.74 3.375,1.958 0.302,0.219 10 true *1

Install and uniformly tighten the 6 bolts and 4 nuts in several passes.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Nut

HINT:

Tighten the inner installation bolts of the intake manifold before tightening the outer bolts.



Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 17129 3.INSTALL INTAKE AIR SURGE TANK

a.

Install a new gasket to the intake air surge tank.


b.
A221465E05
0.115,1.76 0.365,1.969 0.25,0.208 10 true *1 2.469,1.573 2.74,1.781 0.271,0.208 10 true *1

Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Text in Illustration
*1 Nut


c.

Install the No. 1 surge tank stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Attach the wire harness clamp.


e.

Install the No. 2 surge tank stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Install the throttle body bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
A225183E01
2.241,2.234 2.651,2.399 0.409,0.165 10 120° 1.949,0.682 2.277,0.838 0.328,0.156 10 45° 1.273,2.327 1.273,2.657 false 1.275,2.672 1.314,2.326 false 2.471,0.137 2.644,0.281 0.172,0.144 10 *a 1.181,2.718 1.359,2.883 0.178,0.164 10 *b 1.893,2.74 2.071,2.904 0.178,0.164 10 *a 2.765,2.079 2.943,2.244 0.178,0.164 10 *c

Connect the No. 1 ventilation hose.


h.

Connect the No. 1 vacuum switching valve connector.


i.

Connect the No.1 fuel feed hose.

Text in Illustration
*a Front
*b Matchmark
*c Top

HINT:

Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



j.
A225184E01
0.983,1.342 1.003,1.642 false 1.002,1.649 1.033,1.342 false 0.922,1.742 1.100,1.906 0.178,0.164 10 *b 2.021,1.61 2.199,1.775 0.178,0.164 10 *a 1.642,1.248 1.820,1.412 0.178,0.164 10 *c

Connect the throttle body connector.


k.

Connect the No. 4 water by-pass hose.


l.

Connect the No. 5 water by-pass hose.

HINT:

Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



m.

Connect the 2 heater hose clamps.

Text in Illustration
*a Front
*b Matchmark
*c RH


Hide 17360 4.INSTALL AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

a.
A226131E01
2.567,0.171 2.741,0.334 0.174,0.163 10 *a 0.633,0.167 0.808,0.330 0.174,0.163 10 *1 2.012,0.643 2.186,0.806 0.174,0.163 10 *b 1.678,0.852 1.853,1.015 0.174,0.163 10 *2 1.957,0.946 2.272,1.103 0.315,0.157 10 60° 1.186,0.697 0.949,0.249 false 0.949,0.249 0.847,0.249 false 1.35,0.709 1.575,0.93 false 1.575,0.93 1.664,0.93 false

for Bank 1 Side:

Align the paint mark with the projection and connect the air tube assembly to the emission control valve set.

Text in Illustration
*1 Rib
*2 Paint Mark
*a RH Side
*b Upper

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



b.
A226132E01
0.333,1.128 0.482,1.278 0.150,0.150 10 *1 1.375,0.225 1.525,0.374 0.150,0.150 10 *2 2.481,0.263 2.631,0.412 0.150,0.150 10 *a 3.142,0.673 3.292,0.823 0.150,0.150 10 *b 0.714,0.894 0.62,1.213 false 0.62,1.213 0.531,1.213 false 0.956,0.837 1.219,0.301 false 1.219,0.301 1.342,0.301 false 3.076,1.141 3.400,1.297 0.324,0.156 10 60°

for Bank 2 Side:

Align the paint mark with the projection and connect the air tube assembly to the No. 2 emission control valve set.

Text in Illustration
*1 Paint Mark
*2 Rib
*a Upper
*b LH Side

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



c.

Install the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17881 5.INSTALL NO. 1 AIR CLEANER HOSE

a.
A225179E01
1.649,3.75 2.007,3.892 0.358,0.142 10 90° 2.547,0.874 2.896,1.016 0.349,0.142 10 90° 2.15,0.462 2.509,0.604 0.359,0.142 10 60° 0.776,3.903 0.667,4.051 false 0.667,4.051 0.487,4.051 false 0.881,3.841 0.619,3.571 false 0.619,3.572 0.512,3.572 false 0.293,3.976 0.444,4.127 0.151,0.150 10 *a 0.297,3.476 0.448,3.627 0.151,0.150 10 *b 1.902,0.442 2.054,0.592 0.151,0.150 10 *c 1.594,0.854 1.745,1.004 0.151,0.150 10 *d 2.374,3.239 2.525,3.389 0.151,0.150 10 *c 2.839,3.755 2.990,3.905 0.151,0.150 10 *e 1.361,0.545 1.521,0.691 0.159,0.145 10 *1 2.097,0.815 1.747,0.625 false 1.747,0.625 1.553,0.625 false

Install the air cleaner hose with the 2 clamps.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*1 Paint mark
*a Protrusion
*b Groove
*c Top
*d RH
*e Front


b.

Install the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the vacuum hose and ventilation hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



d.

Attach the wire harness clamp.


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11259 11.INSTALL V-BANK COVER

a.
A229926E01
3.134,0.612 3.284,0.759 0.150,0.147 10 *1 2.751,0.698 3.103,0.698 false 1.132,0.577 1.282,0.723 0.150,0.147 10 *2 0.932,0.814 0.996,0.652 false 0.996,0.652 1.109,0.652 false

Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.

Text in Illustration
*1 Pin
*2 Hook


Hide 51405A 12.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY