Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM27T0E _51 Engine / Hybrid System _053662 1GR-FE ENGINE MECHANICAL _0260493 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

for Automatic Transmission:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, cylinder head LH, camshaft, No. 2 camshaft, No. 3 camshaft, No. 4 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 12281A 1.INSTALL ENGINE HANGER

a.
U147659E06
3,0.469 2.917,0.469 2.917,0.469 2.76,0.688 false 0.365,0.635 0.563,0.635 0.563,0.635 0.792,0.844 true 0.146,0.573 0.313,0.75 0.167,0.177 10 false *1 3.083,0.385 3.271,0.563 0.188,0.177 10 false *2 3.104,1.771 3.208,1.938 0.104,0.167 10 false 1 2.396,1.948 2.5,2.115 0.104,0.167 10 false 2 1.198,1.813 1.302,1.979 0.104,0.167 10 false 1 0.458,1.719 0.563,1.885 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



Hide 2.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


c.

Place the engine onto a work bench.


Hide 3.INSTALL ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Slowly lower the engine into the engine compartment.


c.
A223677E04
1.854,0.417 2,0.594 0.146,0.177 10 false A 1.396,0.156 1.542,0.333 0.146,0.177 10 false A 0.49,0.135 0.667,0.323 0.177,0.188 10 true B 1.427,1.177 1.573,1.354 0.146,0.177 10 true B 1.885,1.229 2.031,1.406 0.146,0.177 10 true B 3.01,0.427 3.156,0.604 0.146,0.177 10 true B

Install the front engine mounting insulator LH with the 3 nuts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Install the front engine mounting insulator RH with the 3 nuts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
A247325E03
0.99,3.677 0.74,3.5 0.74,3.5 0.604,3.5 true 2.188,3.667 1.938,3.479 1.938,3.479 1.802,3.479 true 1.094,3.833 1.24,4.115 1.24,4.115 1.24,4.208 false 2.302,3.844 2.448,4.125 2.448,4.125 2.448,4.219 false 1,2.76 1.177,2.948 0.177,0.188 10 false *a 2.365,2.76 2.542,2.948 0.177,0.188 10 false *b 0.375,3.438 0.531,3.594 0.156,0.156 10 false *1 1.198,4.271 1.354,4.427 0.156,0.156 10 false *2 1.615,3.417 1.771,3.573 0.156,0.156 10 false *1 2.385,4.25 2.542,4.406 0.156,0.156 10 false *2

For RHD vehicles only:

When tightening the nut closer to the rear of the vehicle for the engine mounting bracket on the right side, make sure that the claw (stopper) of the bolt does not protrude past the rear edge of the bracket.


Text in Illustration
*1 Claw (Stopper)
*2 Bracket
*a Correct
*b Incorrect


e.

Remove the 2 engine hangers and 4 bolts.


Hide 32101 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A384115E01
0.635,1.24 0.854,1.24 false 1.406,1.281 1.625,1.281 false 2.229,1.125 2.448,1.125 false 2.052,1.052 2.365,1.25 0.313,0.198 10 false *3 1.208,1.198 1.521,1.396 0.313,0.198 10 false *2 0.458,1.156 0.771,1.354 0.313,0.198 10 false *1

Install the front spacer, drive plate and rear spacer to the crankshaft.

Text in Illustration
*1 Front Spacer
*2 Drive Plate and Ring Gear
*3 Rear Spacer
V100135

Automatic Transmission Side

HINT:

As the front spacer, drive plate and ring gear and rear spacer are not reversible, be sure to install it in the direction shown in the illustration.



c.

Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A224777E06
1.677,0.281 1.781,0.438 0.104,0.156 10 true 1 1.646,1.677 1.792,1.833 0.146,0.156 10 true 2 2.344,1 2.469,1.167 0.125,0.167 10 true 3 0.958,0.958 1.083,1.125 0.125,0.167 10 true 4 2.167,0.49 2.271,0.646 0.104,0.156 10 true 5 1.125,1.5 1.26,1.656 0.135,0.156 10 true 6 2.177,1.521 2.281,1.677 0.104,0.156 10 true 7 1.188,0.438 1.292,0.594 0.104,0.156 10 true 8

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing.



Hide 13405 5.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Temporarily install the flywheel with 8 new bolts.


c.

Install and tighten the 8 bolts uniformly in several steps.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.

Mark the top of the bolts with paint.


e.

Tighten the 8 bolts 90° in the same sequence.


f.

Check that the paint marks are now at a 90° angle to the top.


Hide 31250 6.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 7.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 8.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 9.CONNECT OIL COOLER TUBE SUB-ASSEMBLY (for Automatic Transmission)

a.

Connect the oil cooler tube with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 88704 10.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Connect the suction hose with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 12371 11.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for Manual Transmission)

Hide 12371 12.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for Automatic Transmission)

Hide 33030 13.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 35000 14.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 23801P 17.CONNECT NO. 1 AND NO. 2 FUEL PIPES

a.

Connect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Install the No. 2 fuel pipe clamp to the fuel tube connector.


Hide 18.CONNECT HEATER WATER HOSE ASSEMBLY

a.
U147622E04
0.042,0.052 0.25,0.24 0.208,0.188 10 true *A 0.073,1.667 0.281,1.854 0.208,0.188 10 true *B 2.896,0.958 3.031,1.125 0.135,0.167 10 false A 2.896,2.677 3.031,2.844 0.135,0.167 10 false A 0.208,1.938 0.344,2.104 0.135,0.167 10 false B 1.927,0.604 2.063,0.771 0.135,0.167 10 false A 1.865,2.271 2,2.438 0.135,0.167 10 false A 0.854,2.271 0.99,2.438 0.135,0.167 10 false B 2.167,0.552 2.344,0.719 0.177,0.167 10 false *a 2.115,2.24 2.292,2.406 0.177,0.167 10 false *a 2.479,0.885 2.656,1.052 0.177,0.167 10 false *b 2.479,1.26 2.656,1.427 0.177,0.167 10 false *b 2.417,2.573 2.594,2.74 0.177,0.167 10 false *b 2.417,2.948 2.594,3.115 0.177,0.167 10 false *b 1.438,2.979 1.615,3.146 0.177,0.167 10 false *b 1.458,2.573 1.635,2.74 0.177,0.167 10 false *b 1.063,2.229 1.24,2.396 0.177,0.167 10 false *c 1.396,2.396 1.625,2.573 0.229,0.177 10 false 30° 1.385,2.802 1.615,2.979 0.229,0.177 10 false 30°

w/ Rear heater:

Connect the 4 hoses and heater water hose.

Text in Illustration
*A w/o Rear Heater
*B w/ Rear Heater
*a Top
*b LH
*c RR

HINT:

The direction of the hose clamp is indicated in the illustration.



b.

w/o Rear heater

Connect the 2 hoses and heater water hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



Hide 82121 19.CONNECT ENGINE WIRE

a.

Connect the ECM connector.

i.
A226129E01
3.007,0.331 3.191,0.510 0.184,0.179 10 *1 2.912,1.633 3.096,1.812 0.184,0.179 10 *2 2.975,0.427 2.841,0.427 2.841,0.427 2.611,0.751 false 2.414,1.25 2.68,1.725 2.68,1.725 2.895,1.725 false

Attach the grommet to the wire harness support.

Text in Illustration
*1 Grommet
*2 Wire Harness Support


ii.

Pass the wire harness into the vehicle and install the wire harness support.


iii.
A225400E02
0.042,0.052 0.281,0.271 0.24,0.219 10 false *A 0.063,2.333 0.302,2.552 0.24,0.219 10 false *B

Connect the 9 connectors and attach the clamp.

Text in Illustration
*A for LHD
*B for RHD




c.
A222166

Connect the connector and install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 20.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 17105 24.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 25.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17362 26.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17104 28.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 29.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 45203 30.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)

a.

for Power tilt and power telescopic steering column:

Connect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>INSTALLATION).


b.

for Manual tilt and manual telescopic steering column:

Connect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>INSTALLATION).


Hide 17361 31.INSTALL AIR TUBE (w/ Secondary Air Injection System)

Hide 17410 33.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17360 40.INSTALL AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 32907C 43.CONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

Hide 32907C 44.CONNECT OIL COOLER TUBE (w/ Warmer)

Hide 53294C 48.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 49.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 52521 50.INSTALL FRONT BUMPER CENTER UPPER RETAINER

Hide 52119A 53.INSTALL FRONT BUMPER COVER

a.

Install the front bumper cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION).


Hide 74431 55.INSTALL BATTERY TRAY

Hide 28800 56.INSTALL BATTERY

Hide 28800A 58.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 55781E 61.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Install the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 62.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 63. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 53292A 68.INSTALL UPPER RADIATOR SUPPORT SEAL

a.

Install the upper radiator support seal with the 13 clips.


Hide 53736B 69.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Install the front No. 1 fender apron to frame seal with the 5 clips.


Hide 53737A 70.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

a.

Install the front No. 1 fender apron to frame seal with the 5 clips.


Hide 53736 71.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal with the 5 clips.


Hide 53737B 72.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal with the 5 clips.


Hide 51450 73.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

a.

Install the rear engine under cover with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51495 74.INSTALL TRANSMISSION UNDER COVER

a.

Install the transmission under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 75.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Hook the engine under cover to the vehicle body as shown in the illustration.


b.

Install the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 76.INSTALL FRONT BUMPER COVER LOWER

a.

Install the front bumper cover lower with the 5 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 77.PERFORM RESET MEMORY (for Automatic Transmission)

Hide 53301 81.INSTALL HOOD SUB-ASSEMBLY

a.
A229697

Install the hood with the 8 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Connect the washer nozzle hose.


Hide 53301 82.ADJUST HOOD SUB-ASSEMBLY