Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side) › from 2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261116 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72691B 1.INSTALL REAR SEAT CUSHION LOCK STRIKER

a.

Install the striker with the 2 bolts.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 72602B 2.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH

B237984C01
0.208,1.792 0.438,1.979 0.229,0.188 10 true (1) 2.594,0.25 2.865,0.438 0.271,0.188 10 true (2)

a.

Attach the claw and install the striker with the 2 bolts.


b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 64712F 4.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

Hide 64937A 5.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

Hide 64725D 6.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 73233A 7.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 57411D 10.INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

Hide 58574A 11.INSTALL REAR FLOOR REAR MAT SUPPORT PLATE

Hide 64717A 13.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER

Hide 64910M 14.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 62332C 15.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 17.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)

a.

for Face to Face Seat Type:

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION).


Hide 72678 18.INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH

a.

Attach the cable clamp to connect the cable.


b.
B237982

Move the cover in the direction of the arrow to attach the 2 guides.


c.

Attach the 6 claws to install the lever base.


Hide 71304C 19.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.

Install the hinge with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 20.INSTALL REAR SEATBACK ASSEMBLY LH

B613923C01
2.865,1.49 2.99,0.375 2.99,0.375 3.125,0.375 true 2.323,3.052 2.74,3.313 0.417,0.26 12 false *A 3.146,0.292 3.417,0.469 0.271,0.177 10 false *a 2.417,3.969 2.646,4.208 0.229,0.24 10 true (1) 1.292,4.135 1.521,4.375 0.229,0.24 10 true (2) 2.854,1.979 3.083,2.208 0.229,0.229 10 true (3)
*A w/ Seat Belt Warning System
*a Positioning Wire
V100135

Bolt
V100136

Connector


a.

Fold down the seatback, set the seatback positioning wire on the hinge, and then temporarily install the bolt to the hinge.

NOTICE:

Be careful not to damage the vehicle body.



b.

Restore the seatback to the upright position and temporarily install the seatback with the 2 bolts.


c.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


d.

w/ Seat Belt Warnig System:

i.

Connect the connector.



Hide 71890A 21.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

a.

Attach the 4 claws and 5 clips to install the carpet.


Hide 72996A 22.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


b.

Restore the seatback to the upright position and lock it.


Hide 71940A 23.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the headrest.


Hide 24.INSTALL REAR SEAT CUSHION ASSEMBLY LH

B240248E04
0.594,1.615 0.802,1.802 0.208,0.188 10 false (1) 1.604,1.938 1.813,2.125 0.208,0.188 10 false (2)

a.

Temporarily install the seat cushion with the 2 bolts.

NOTICE:

Be careful not to damage the vehicle body.



b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


c.

Lock the seat cushion.


Hide 71639 25.INSTALL REAR SEAT CUSHION HINGE COVER LH

a.

Attach the 3 claws to install the cover.


Hide 71629 26.INSTALL REAR SEAT CUSHION HINGE COVER RH

a.

Attach the 3 claws to install the cover.


Hide 27.CHECK SEAT BELT WARNING SYSTEM (w/ Seat Belt Warning System)