Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
66426B
1.INSTALL REAR NO. 3 SIDE RAIL SPACER LH
Attach the 2 claws to install the rear No. 3 side rail spacer LH.
66416
2.INSTALL REAR NO. 3 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
66425A
3.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the 2 claws to install the rear No. 2 side rail spacer LH.
66415A
4.INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Use the same procedure described for the LH side.
66424
5.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the 2 claws to install the rear side rail spacer LH.
66414A
6.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Use the same procedure described for the LH side.
64715C
7.INSTALL DECK SIDE TRIM COVER LH
Attach the 3 claws and 2 guides to install the deck side trim cover LH.
64766B
8.INSTALL QUARTER TRIM JACK COVER
Attach the 3 claws and 2 guides to install the quarter trim jack cover.
62627B
9.INSTALL QUARTER TRIM COVER
Use the same procedure for the other quarter trim cover.
Attach the 2 claws to install the quarter trim cover.
73372
10.INSTALL REAR SEAT SHOULDER BELT HANGER LH
Attach the claw and guide to install the rear seat shoulder belt hanger LH.
73371
11.INSTALL REAR SEAT SHOULDER BELT HANGER RH
Use the same procedure described for the LH side.
62477A
12.INSTALL ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)
Attach the 4 claws and 2 guides to install the roof side inner garnish cap LH.
62476A
13.INSTALL ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)
Use the same procedure described for the LH side.
73034
14.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 6 claws to install the rear belt anchor plate sub-assembly LH.
73033
15.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
73024
16.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 5 claws to install the front belt anchor plate sub-assembly LH.
73023
17.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
63310
18.INSTALL ROOF HEADLINING ASSEMBLY
Place the roof headlining into the vehicle through the back door.
Be careful not to damage the roof headlining when placing it in the cabin.
w/o Sliding Roof:
Attach the 2 clips to install the roof headlining assembly.
| *a | Guide |
| *b | Fastener |
w/ Sliding Roof:
Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining assembly.
| *a | Guide |
| *b | Fastener |
w/ Rear Seat Entertainment System:
Attach the 2 clips, 2 guides and 6 fasteners to install the roof headlining assembly.
w/ Rear Seat Entertainment System:
Connect the 2 connectors.
Connect the connector and attach the 3 clamps to the rear pillar RH.
Connect the 2 connectors and attach the clamp to the rear pillar LH.
Connect the 2 connectors and attach the 3 clamps to the front pillar RH.
Install the bolt.
Connect the 2 connectors and attach the 3 clamps to the front pillar LH.
w/ Digital Audio Broadcasting Antenna:
Connect the connector and attach the wire harness clamp.
w/ Pre-collision System:
Attach the hook to install the camera earth with the bolt.
w/ Sliding Roof
Connect the drive gear connector.
w/ Rain Sensor:
Connect the rain sensor connector.
w/ EC Mirror:
Connect the inner mirror connector.
w/ Pre-collision System:
Connect the 3 connectors.
74348
19.INSTALL VISOR HOLDER
Use the same procedure for the other visor holder.
Attach the 2 claws.
Push in the visor holder to install it.
74320
20.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
74310
21.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74318
22.INSTALL VISOR BRACKET COVER LH
Use the same procedure for the other visor bracket cover.
Attach the 4 claws to install the visor bracket cover LH.
74317
23.INSTALL VISOR BRACKET COVER RH
Use the same procedure described for the LH side.
86160T
24.INSTALL REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)
87217D
25.INSTALL REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)
62432B
26.INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH
| *a | New Clip |
Install 3 new clips to the No. 1 roof side rail garnish LH.
Attach the 3 clips to install the No. 1 roof side rail garnish LH.
62431B
27.INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH
Use the same procedure described for the LH side.
86295
28.INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)
81240D
29.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
81240
30.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
86466D
31.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466E
32.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
87834
33.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Pre-collision System)
89943
34.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
81260A
35.INSTALL MAP LIGHT ASSEMBLY
74611B
36.INSTALL ASSIST GRIP (w/ Rear No. 2 Seat)
Use the same procedure for the other assist grip.
Install the assist grip with the 2 bolts.
Attach the 4 claws to close the 2 covers.
74610U
37.INSTALL REAR ASSIST GRIP ASSEMBLY LH
Assemble the rear assist grip assembly LH, 2 clips and 2 covers as shown in the illustration.
Install the rear assist grip sub-assembly LH.
74610V
38.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
74610A
39.INSTALL ASSIST GRIP SUB-ASSEMBLY
Assemble the assist grip sub-assembly, 2 clips and 2 covers as shown in the illustration.
Install the assist grip sub-assembly.
62640P
40.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH
w/o Rear No. 2 Seat:
Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.
w/ Rear No. 2 Seat:
Attach the 4 clips and 2 guides and pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel.
Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.
62630P
41.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
62520P
42.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel assembly LH.
Attach the 2 clips and 2 guides to install the front quarter trim panel assembly LH.
62510P
43.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
64740C
44.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:
Pass the rear seatback lock control lever base through the deck trim side panel assembly LH.
Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.
Install the 4 bolts and 2 screws.
Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly LH.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:
Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.
Install the 2 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
w/ Rear No. 2 Seat:
Attach the 4 clips and 8 claws to install the deck trim side panel assembly LH.
Install the 2 bolts and 2 screws.
Install the rear No. 2 seat outer belt floor anchor with the bolt.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
64730B
45.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:
Connect each connector.
Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.
Attach the 5 clips and 8 claws to install the deck trim side panel assembly RH.
Install the 4 bolts and screw.
Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:
Connect each connector.
Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.
Install the 2 bolts and screw.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
w/ Rear No. 2 Seat:
Connect each connector.
Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.
Install the 2 bolts and screw.
Install the rear No. 2 seat outer belt floor anchor with the bolt.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
74603C
46.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)
Use the same procedure for the other assist grip.
Install the assist grip sub-assembly with the 2 bolts.
74617A
47.INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)
Use the same procedure for all assist grip plugs.
Attach the 2 claws to install the assist grip plug.
64712F
48.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover.
64937A
49.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
Use the same procedure for the other No. 1 tonneau cover holder cap.
Attach the 2 claws to install the No. 1 tonneau cover holder cap.
64725D
50.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook by turning it clockwise.
73233A
51.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.
58570C
52.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)
Attach the 4 claws to install the rear floor carpet assembly.
| *A | w/o Deck Rail | *B | w/ Deck Rail |
| *C | for Face to Face Seat Type | *D | w/ Rear Air Conditioning System |
57412C
53.INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)
Install the floor side rail LH with the 3 bolts.
57411D
54.INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)
Use the same procedure described for the LH side.
58574A
55.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.
58401A
56.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)
w/ Rear Air Conditioning System:
Attach the clip to install the No. 1 deck board sub-assembly.
w/o Rear Air Conditioning System:
Attach the clip to install the No. 1 deck board sub-assembly.
64717A
57.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)
| *1 | Luggage Hold Belt Striker |
Use the same procedure for the other front luggage compartment trim cover.
Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.
Attach the 4 claws to install the cap.
64910M
58.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Install the tonneau cover assembly.
62412
59.INSTALL CENTER PILLAR GARNISH LH
Pass the front seat outer belt floor anchor through the center pillar garnish LH.
Attach the 2 clips and 2 guides to install the center pillar garnish LH.
Install the bolt.
62411
60.INSTALL CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
74611G
61.INSTALL NO. 2 ASSIST GRIP
Use the same procedure for the other No. 2 assist grip.
Attach the 2 claws to install the No. 2 assist grip.
Install the 2 bolts.
74638
62.INSTALL NO. 2 ASSIST GRIP PLUG LH
Use the same procedure for the other front No. 2 assist grip plug.
Attach the 2 claws to install the front No. 2 assist grip plug LH.
74637
63.INSTALL NO. 2 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
62414A
64.INSTALL LOWER CENTER PILLAR GARNISH LH
Attach the 4 claws and 2 clips to install the lower center pillar garnish LH.
Install the front seat outer belt floor anchor with the bolt.
62413A
65.INSTALL LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
73233
66.INSTALL OUTER LAP BELT ANCHOR COVER
Use the same procedure for the other outer lap belt anchor cover.
Attach the 3 claws to install the outer lap belt anchor cover.
62332C
67.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
| *a | Paint Mark |
| *b | Mark Position |
Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install the rear door opening trim weatherstrip LH as shown in the illustration.
62331C
68.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
67918D
69.INSTALL REAR DOOR SCUFF PLATE LH
Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.
67917C
70.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
67934
71.INSTALL INSIDE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
Install the quarter scuff plate LH with the 2 bolts.
67933
72.INSTALL INSIDE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
58371F
73.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
Use the same procedure for all rear No. 1 floor step covers.
Attach the 2 claws to install the rear No. 1 floor step cover.
62212
74.INSTALL FRONT PILLAR GARNISH LH
Attach the 3 guides to install the front pillar garnish LH.
62211
75.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74611F
76.INSTALL NO. 1 ASSIST GRIP
Use the same procedure for the other No. 1 assist grip.
Attach the 2 claws to install the No. 1 assist grip.
Install the 2 bolts.
74616C
77.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH
Use the same procedure for the other front No. 1 assist grip plug.
Attach the 2 claws to install the front No. 1 assist grip plug LH.
74615E
78.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
62312B
79.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
| *a | Paint Mark |
| *b | Mark Position |
Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install the front door opening trim weatherstrip LH as shown in the illustration.
62311B
80.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
81.INSTALL COWL SIDE TRIM BOARD LH
Attach the clip and claw to install the cowl side trim board LH.
Attach the clip and claw in the order shown in the illustration.
Install the clip.
62111C
82.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67920
83.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.
67910
84.INSTALL DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure described for the LH side.
85.INSTALL REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)
for 60/40 Split Double-folding Seat Type LH Side:
for 60/40 Split Double-folding Seat Type RH Side:
86.INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
for 60/40 Split Slide Walk-in Seat Type LH Side:
for 60/40 Split Slide Walk-in Seat Type RH Side:
87.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
for Manual Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)>INSTALLATION
for Power Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>INSTALLATION
for Face to Face Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION
88.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
89. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART