Wear protective gloves. Sharp areas on the parts may injure your hands.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
72691B
1.INSTALL REAR SEAT CUSHION LOCK STRIKER
Install the striker with the 2 bolts.
72601
2.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY RH
Attach the claw and install the striker with the 2 bolts.
Tighten the bolts in the order indicated in the illustration.
64730B
3.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
64712F
4.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
64937A
5.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
64725D
6.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
73233A
7.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
58570C
8.INSTALL REAR FLOOR CARPET ASSEMBLY
57412C
9.INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)
57411D
10.INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)
58574A
11.INSTALL REAR FLOOR REAR MAT SUPPORT PLATE
58401A
12.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY
64717A
13.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER
64910M
14.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
62331C
15.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
67917C
16.INSTALL REAR DOOR SCUFF PLATE RH
17.INSTALL REAR NO. 2 SEAT ASSEMBLY RH
for Face to Face Seat Type:
Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION).
72677A
18.INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH
Attach the cable clamp to connect the cable.
Move the cover in the direction of the arrow to attach the 2 guides.
Attach the 6 claws to install the lever base.
71303C
19.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
Install the hinge with the bolt.
20.INSTALL REAR SEATBACK ASSEMBLY RH
| *A | w/ Seat Belt Warning System |
| *a | Positioning Wire |
|
Bolt |
|
Connector |
Fold down the seatback, set the seatback positioning wire on the hinge, and then temporarily install the bolt to the hinge.
Be careful not to damage the vehicle body.
Restore the seatback to the upright position and temporarily install the seatback with the 2 bolts.
Tighten the bolts in the order indicated in the illustration.
w/ Seat Belt Warning System:
Connect the connector.
Attach the 2 claws and connect the outer belt with the bolt.
71880A
21.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
Attach the 2 claws and 5 clips to install the carpet.
72996A
22.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the cover.
Restore the seatback to the upright position and lock it.
71940A
23.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the headrest.
24.INSTALL REAR SEAT CUSHION ASSEMBLY RH
Temporarily install the seat cushion with the 2 bolts.
Be careful not to damage the vehicle body.
Tighten the bolts in the order indicated in the illustration.
Lock the seat cushion.
71629A
25.INSTALL REAR SEAT CUSHION HINGE COVER RH
Attach the 3 claws to install the cover.
71629
26.INSTALL REAR SEAT CUSHION HINGE COVER LH
Attach the 3 claws to install the cover.
27.CHECK SEAT BELT WARNING SYSTEM (w/ Seat Belt Warning System)