Wear protective gloves. Sharp areas on the parts may injure your hands.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
78920B
1.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH
Install the cable to the seat cushion frame.
Attach the 3 cable clamps and connect the cable.
Install 2 new cable ties.
73709A
2.INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY
Install the bracket with the bolt.
72720B
3.INSTALL REAR SEATBACK INNER ADJUSTER ASSEMBLY LH
| *a | Bolt A |
| *b | Bolt B |
Install the cover and adjuster with the 2 bolts.
71018
4.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH
Install the seatback frame and bracket with the 4 bolts.
72830B
5.INSTALL REAR CENTER SEAT ARMREST BUSH
Attach the 3 claws to install the bush.
72569
6.INSTALL SEATBACK STOPPER PLATE
Install the plate with 3 bolts.
71878E
7.INSTALL REAR SEAT RECLINING COVER INNER RH
Attach the 2 guides to install the cover.
71879E
8.INSTALL REAR SEAT RECLINING COVER INNER LH
Attach the 2 guides to install the cover.
71879F
9.INSTALL REAR SEAT INNER RECLINING COVER LH
Attach the 2 guides and 2 claws to install the cover.
72620B
10.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Install the cable to the seatback frame.
Attach the 2 cable clamps and connect the cable.
73320A
11.INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
73187A
12.INSTALL REAR SEAT SHOULDER BELT GUIDE
Attach the 4 guides to install the belt guide.
Connect the outer belt to the belt guide.
Attach the 2 claws to close the cover.
71812C
13.INSTALL RECLINING ADJUSTER COVER LH
Attach the 4 claws to install the cover.
Install the 4 screws.
71834H
14.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
Attach the 2 claws to install the cover.
71078S
15.INSTALL SEPARATE TYPE REAR SEATBACK COVER
Install the seatback cover with 2 new hog rings and attach the fastening tape.
Using hog ring pliers, install the new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *a | Hog Ring Pliers | *b | Fastening Tape |
16.INSTALL SEATBACK COVER WITH PAD
Connect the outer belt to the seatback cover with pad.
Attach the 2 hooks to install the seatback cover with pad.
71931B
17.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 8 claws to install the 4 supports.
72058A
18.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Connect the cable in the order shown in the illustration to install the lever.
Install the 2 screws.
72615C
19.INSTALL REAR SEATBACK LOCK STRIKER COVER
Attach the guide and claw to install the cover.
73375B
20.INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH
Connect the outer belt to the cover.
Attach the 4 claws to install the cover.
73237A
21.INSTALL SHOULDER BELT ANCHOR COVER
Attach the 2 claws and 2 guides to install the cover.
71956C
22.INSTALL REAR SEAT ARMREST SUPPORT
Install the armrest support to the armrest hinge.
71281A
23.INSTALL REAR SEAT CENTER ARMREST HINGE
Install the armrest hinge with the screw.
72830
24.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
Install the center armrest and bush with the 2 bolts.
71837D
25.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the guide to install the cover.
Install the screw.
79185
26.INSTALL NO. 1 SEATBACK PAD LH
Install the seatback pad.
Close the 2 fasteners, and then close the seatback cover.
| *a | Hog Ring Pliers |
Using hog ring pliers, install 6 new hog rings.
Attach the 3 fastening tapes and close the cover.
| *a | Protruding Part |
Connect the outer belt with the bolt.
Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.
72996A
27.INSTALL REAR SEATBACK COVER
Attach the 8 claws to install the 2 covers.
71076S
28.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
| *a | Hog Ring Pliers |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
71647F
29.INSTALL REAR SEAT INNER CUSHION EDGE PROTECTOR LH
Install the protector with new tack pins.
73380C
30.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73390A
31.INSTALL REAR SEAT INNER BELT ASSEMBLY
32.INSTALL SEAT CUSHION COVER WITH PAD
| *a | Hog Ring Pliers |
Using hog ring pliers, install the seatback cover with pad with new hog rings.
Install the carpet with new tack pins.
71585
33.INSTALL REAR NO. 2 SEAT HINGE COVER RH
Attach the 3 claws to install the cover.
71586
34.INSTALL REAR NO. 2 SEAT HINGE COVER LH
Attach the 3 claws to install the cover.
72908B
35.INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
Temporarily install the under cover to the seat cushion frame.
72649
36.INSTALL REAR SEAT CUSHION SUPPORT SPRING
Install the spring to the seat cushion frame
Use the same procedure for both springs.
78917
37.INSTALL FOLD SEAT LEG LOCK CUSHION
Install the cushion to the protector.
Use the same procedure for both cushions.
71647G
38.INSTALL REAR SEAT CUSHION EDGE PROTECTOR
Install the protector to the cushion frame.
Use the same procedure for both protectors.
71301D
39.INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH
Install the hinge.
Install the pin to the hinge.
Install a new E-ring.
71305C
40.INSTALL REAR SEAT STAY SUB-ASSEMBLY
Connect the seat stay ball-joint to the seat hinge.
It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.
71302D
41.INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
Install the spring of the seat stay ball-joint.
Temporarily install the seat hinge and seat stay as a unit.
Raise the under cover.
Connect the seat stay to the seat cushion frame.
Connect the reclining release handle to the under cover.
Install the 5 screws.
Attach the 10 claws to install the under cover.
Install the pin to the hinge.
Install a new E-ring.
72779
42.INSTALL REAR SEAT HINGE PAWL GUIDE
Attach the 4 claws to install the pawl guide.
Use the same procedure for both pawl guides.
72205B
43.INSTALL SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY
Install the pin as shown in the illustration.
Install the stopper.
Use the same procedure for both pins.
71876K
44.INSTALL REAR RECLINING ADJUSTER INSIDE COVER LH
Attach the 2 claws to install the cover.
Install the 2 screws.
71324G
45.INSTALL REAR NO. 2 SEAT CUSHION
Install the cushion with the screw.
71833A
46.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
Attach the 2 hooks.
Attach the guide and 2 claws to install the cover.
Install the 2 screws.
71844D
47.INSTALL REAR SEAT RECLINING COVER LH
Attach the guide and 2 claws to install the cover.
Install the 2 screws.