Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C111  GNSS Antenna Circuit Short to Ground  B15C113  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C111 GNSS Antenna Circuit Short to Ground Current to the telephone antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is turned to ON
(Short circuit)
·

Telephone Transceiver Assembly

·

Telephone antenna assembly

·

Antenna divider (w/ Heated Windshield Defroster System)

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly (Roof)

·

Telephone antenna cord sub-assembly (I/P)


B15C113 GNSS Antenna Circuit Open Current to the telephone antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is turned to ON
(Open circuit)
·

Telephone Transceiver Assembly

·

Telephone antenna assembly

·

Antenna divider (w/ Heated Windshield Defroster System)

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly (Roof)

·

Telephone antenna cord sub-assembly (I/P)



WIRING DIAGRAM

E467085E02
0.24,0.104 3.438,0.438 3.198,0.333 12 false w/o Heated Windshield Defroster System: 5.719,3.802 7.156,4.25 1.438,0.448 10 false Telephone Transceiver Assembly 3.948,1.188 4.271,1.469 0.323,0.281 10 false C 5.958,0.948 6.281,1.229 0.323,0.281 10 false 1 2.75,1.188 3.073,1.469 0.323,0.281 10 false B 2.75,1.896 3.073,2.177 0.323,0.281 10 false B 1.542,1.188 1.865,1.469 0.323,0.281 10 false A 1.552,1.896 1.875,2.177 0.323,0.281 10 false A 0.448,2.333 1.104,2.969 0.656,0.635 10 false Telephone Antenna Assembly 1.885,2.594 2.542,3.615 0.656,1.021 10 false Telephone Antenna Cord Sub-assembly (Roof) 2.99,2.583 3.875,3.302 0.885,0.719 10 false No. 2 Antenna Cord Sub-assembly 5.906,1.625 6.229,1.906 0.323,0.281 10 false 1a 3.958,1.896 4.281,2.177 0.323,0.281 10 false C 3.927,1.677 4.25,1.958 0.323,0.281 10 false 2a 3.948,0.99 4.271,1.271 0.323,0.281 10 false 2 2.75,0.979 3.073,1.26 0.323,0.281 10 false 2 2.729,1.677 3.052,1.958 0.323,0.281 10 false 2a 1.521,1.688 1.844,1.969 0.323,0.281 10 false 2a 1.552,0.99 1.875,1.271 0.323,0.281 10 false 2 6.292,1.198 6.792,1.469 0.5,0.271 10 false GPS2 5.104,2.594 5.781,3.688 0.677,1.094 10 false Telephone Antenna Cord Sub-assembly (I/P) 4.635,1.198 5.115,1.458 0.479,0.26 10 false H106 4.625,1.885 5.125,2.188 0.5,0.302 10 false H106 4.76,0.969 5.083,1.25 0.323,0.281 10 false 4 4.688,1.667 5.01,1.948 0.323,0.281 10 false 4a 5.823,1.188 6.302,1.521 0.479,0.333 10 false H109 5.833,1.896 6.354,2.177 0.521,0.281 10 false H109 5.073,1.188 5.573,1.458 0.5,0.271 10 false GPS1

E467084E02
0.177,0.115 3.458,0.49 3.281,0.375 12 false w/ Heated Windshield Defroster System: 0.052,2.281 0.719,2.906 0.667,0.625 10 false Telephone Antenna Assembly 1.229,2.573 1.906,3.594 0.677,1.021 10 false Telephone Antenna Cord Sub-assembly (Roof) 2.406,2.604 3.354,3.313 0.948,0.708 10 false No. 2 Antenna Cord Sub-assembly 3.781,2.354 4.813,2.688 1.031,0.333 10 false Antenna Divider 3.802,2.188 4.833,2.521 1.031,0.333 10 false D 0.938,1.177 1.969,1.51 1.031,0.333 10 false A 0.927,1.896 1.958,2.229 1.031,0.333 10 false A 2.146,1.177 3.177,1.51 1.031,0.333 10 false B 2.156,1.906 3.188,2.24 1.031,0.333 10 false B 5.74,3.813 7.156,4.229 1.417,0.417 10 false Telephone Transceiver Assembly 6.51,1.198 7.156,1.469 0.646,0.271 10 false GPS2 3.344,1.188 3.781,1.438 0.438,0.25 10 false C 3.344,1.896 3.781,2.146 0.438,0.25 10 false C 6.198,0.958 6.573,1.208 0.375,0.25 10 false 1 6.146,1.667 6.521,1.917 0.375,0.25 10 false 1a 4.646,1.052 5.021,1.302 0.375,0.25 10 false 5 4.635,1.781 5.01,2.031 0.375,0.25 10 false 5a 3.615,1.781 3.99,2.031 0.375,0.25 10 false 6a 3.656,1.063 4.031,1.313 0.375,0.25 10 false 6 3.365,0.948 3.74,1.198 0.375,0.25 10 false 2 2.146,0.99 2.521,1.24 0.375,0.25 10 false 2 0.948,0.99 1.323,1.24 0.375,0.25 10 false 2 0.896,1.677 1.271,1.927 0.375,0.25 10 false 2a 2.146,1.677 2.521,1.927 0.375,0.25 10 false 2a 3.323,1.667 3.698,1.917 0.375,0.25 10 false 2a 5.271,2.563 5.969,3.635 0.698,1.073 10 false Telephone Antenna Cord Sub-assembly (I/P) 4.865,1.188 5.302,1.438 0.438,0.25 10 false H106 5,0.938 5.375,1.188 0.375,0.25 10 false 4 4.969,1.635 5.344,1.885 0.375,0.25 10 false 4a 4.875,1.885 5.313,2.135 0.438,0.25 10 false H106 6.052,1.188 6.698,1.458 0.646,0.271 10 false H109 6.052,1.885 6.698,2.156 0.646,0.271 10 false H109 5.302,1.198 5.948,1.469 0.646,0.271 10 false GPS1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.



c.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)
2.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)
a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.
E350951C15
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.26,1.313 1.677,1.271 true 1.063,3.417 1.594,3.583 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.083,1.219 1.396,1.417 0.313,0.198 10 false 2a 0.865,3.323 1.177,3.521 0.313,0.198 10 false 2a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.208,2.656 0.521,2.854 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E350952C14
1.583,0.396 2.021,0.677 0.438,0.281 1.667,2.615 2.104,2.896 0.438,0.281 2.281,1.188 2.802,1.083 true 1.01,3.885 1.594,3.677 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false B 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 0.802,3.813 1,4.01 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b 1.833,2.677 2.323,3.01 0.49,0.333 10 false C
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly [Roof])
*b Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna connector from the telephone antenna cord sub-assembly (roof).


b.

Disconnect the antenna connector from the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE TYPE

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

4.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Heated Windshield Defroster System A
w/ Heated Windshield Defroster System B



A

5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEPHONE ANTENNA CORD SUB-ASSEMBLY [I/P])

B

9.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)
5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEPHONE ANTENNA CORD SUB-ASSEMBLY [I/P])
a.
E467082C03
0.354,0.667 0.854,0.979 0.5,0.313 0.385,2.427 0.885,2.74 0.5,0.313 2.563,1.625 2.344,1.625 2.344,1.625 1.708,0.75 true 2.698,3.313 2.479,3.313 2.479,3.313 2.021,2.833 true 2.5,2.104 2.281,2.104 2.281,2.104 2.01,2.635 true 0.552,0.729 0.865,0.927 0.313,0.198 10 false C 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.125,1.698 0.438,1.896 0.313,0.198 10 false *b 0.479,2.49 0.979,2.74 0.5,0.25 10 false H106 2.604,2.021 3.188,2.24 0.583,0.219 10 false GPS1 2.625,1.531 3.208,1.75 0.583,0.219 10 false 2a 2.75,3.208 3.333,3.427 0.583,0.219 10 false 4a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly [I/P])


Disconnect the C No. 2 antenna cord sub-assembly connector from the instrument panel wire.


b.

Disconnect the H106 telephone antenna cord sub-assembly (I/P) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - H106-4 (GPS1) Always Below 1 Ω
C-2a - H106-4a Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)
E467086C02
1.5,0.427 1.896,0.708 0.396,0.281 1.406,2.688 2,2.979 0.594,0.292 1.865,3.792 2.365,4.156 2.365,4.156 2.542,4.156 true 1.188,2.104 1.344,2.104 1.344,2.104 1.5,1.625 true 0.958,3.438 1.115,3.438 1.115,3.438 1.656,3.771 true 0.698,1 0.854,1 0.854,1 1.417,1.438 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.979,2.01 1.292,2.208 0.313,0.198 10 false 4a 2.594,4.094 2.906,4.292 0.313,0.198 10 false 1a 1.542,0.49 2,0.75 0.458,0.26 10 false H106 1.542,2.75 2.031,2.948 0.49,0.198 10 false H109 0.156,2.594 0.469,2.792 0.313,0.198 10 false *b 0.521,3.375 1.021,3.604 0.5,0.229 10 false GPS2 0.281,0.927 0.781,1.156 0.5,0.229 10 false GPS1
*a Front view of wire harness connector
(to Wire Harness)
*b Front view of wire harness connector
(to Telephone Antenna Assembly)


a.

Disconnect the antenna connector from the wire harness.


b.

Disconnect the antenna connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H106-4 (GPS1) - H109-1 (GPS2) Always Below 1 Ω
H106-4a - H109-1a Always Below 1 Ω
H106-4 (GPS1) or H109-1 (GPS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)

7.CHECK TELEPHONE ANTENNA ASSEMBLY
a.

Replace the telephone antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL



c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

8.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
8.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)
a.
E350976C14
1.583,0.354 2.021,0.656 0.438,0.302 1.583,2.563 2.021,2.865 0.438,0.302 2.271,1.188 2.552,1.26 true 2.792,3.635 2.927,3.979 true 1.76,0.417 2.063,0.646 0.302,0.229 10 false C 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.771,2.635 2.115,2.854 0.344,0.219 10 false D 2.594,1.208 2.875,1.427 0.281,0.219 10 false 2a 2.938,3.979 3.177,4.188 0.24,0.208 10 false 6a 0.208,2.51 0.521,2.708 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)


Disconnect the C No. 2 antenna cord sub-assembly connector from the wire harness.


b.

Disconnect the D antenna divider connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - D-6 Always Below 1 Ω
C-2a - D-6a Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT ANTENNA DIVIDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT ANTENNA DIVIDER
a.

b.
E241596C15
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
5 - 6 Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P))

NG

11.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P))
a.
E467087C02
1.573,2.604 2,2.917 0.427,0.313 1.573,0.438 2,0.75 0.427,0.313 2.427,1.917 2.25,1.917 2.25,1.917 2.115,1.5 true 2.563,4.125 2.375,4.125 2.375,4.125 2.104,3.646 true 1.979,3.594 1.865,4.125 1.865,4.125 1.719,4.125 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.625,2.677 1.99,2.875 0.365,0.198 10 false H106 2.51,1.823 2.875,2.021 0.365,0.198 10 false 5a 2.604,4.01 2.969,4.208 0.365,0.198 10 false 4a 1.74,0.51 2.146,0.698 0.406,0.188 10 false D 1.313,4.021 1.823,4.26 0.51,0.24 10 false GPS1 0.146,2.427 0.458,2.625 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Antenna Divider)
*b Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly [I/P])


Disconnect the D antenna divider connector.


b.

Disconnect the H106 telephone antenna cord sub-assembly (I/P) connector from the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-5 - H106-4 (GPS1) Always Below 1 Ω
D-5a - H106-4a Always Below 1 Ω
D-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR