Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telephone transceiver assembly detects an error in communication between the telephone transceiver assembly and the center airbag sensor assembly as a result of the telephone transceiver assembly self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C464 Airbag Signal Signal Plausibility Failure Telephone transceiver assembly detects an error in signals from center airbag sensor assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Center airbag sensor assembly

·

Telephone transceiver assembly



WIRING DIAGRAM

B617680E01
2.531,1.125 2.833,1.302 0.302,0.177 10 false 24 1.958,1.125 2.479,1.323 0.521,0.198 10 false GSW3 4.896,1.125 5.406,1.313 0.51,0.188 10 false GSW 4.604,1.125 4.875,1.333 0.271,0.208 10 false 13 1.167,2.073 1.49,2.25 0.323,0.177 10 false G1 1.177,2.24 3.5,2.531 2.323,0.292 10 false Center Airbag Sensor Assembly 4.677,2.063 5.229,2.292 0.552,0.229 10 false G333 4.667,2.229 6.771,2.438 2.104,0.208 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

After turning the ignition switch to off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK DTC

B

2.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
a.
E422011C78
1.469,0.219 1.948,0.458 0.479,0.24 0.719,0.375 0.896,0.375 0.896,0.375 1.104,1.104 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.323,0.292 0.698,0.438 0.375,0.146 10 false GSW 1.563,0.26 2,0.51 0.438,0.25 10 false G333 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly but do not disconnect the connectors.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telephone transceiver assembly while the center airbag sensor assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection G333-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.




Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CENTER AIRBAG SENSOR ASSEMBLY)
4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CENTER AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the G333 telephone transceiver assembly connector.


b.

Disconnect the G1 center airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-13 (GSW) - G1-24 (GSW3) Always Below 1 Ω
G333-13 (GSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR