Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the telephone antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Telephone antenna (main) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly (roof)

·

Telephone antenna cord sub-assembly (I/P)

·

No. 2 antenna cord sub-assembly

·

Harness or connector

·

Telephone transceiver assembly


B15CB13 Telephone Main Antenna Circuit Open Telephone antenna (Main) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly (roof)

·

Telephone antenna cord sub-assembly (I/P)

·

No. 2 antenna cord sub-assembly

·

Harness or connector

·

Telephone transceiver assembly



WIRING DIAGRAM

E467081E02
6.115,2.479 6.917,3.208 0.802,0.729 10 false Telephone Transceiver Assembly 4.333,1.125 4.865,1.406 0.531,0.281 10 false H106 5.802,0.896 6.125,1.177 0.323,0.281 10 false 1 2.438,1.125 2.76,1.406 0.323,0.281 10 false B 2.417,1.771 2.74,2.052 0.323,0.281 10 false B 1.094,1.135 1.417,1.417 0.323,0.281 10 false A 1.104,1.781 1.427,2.063 0.323,0.281 10 false A 0.156,2.271 0.813,2.906 0.656,0.635 10 false Telephone Antenna Assembly 1.135,2.49 2.375,3.271 1.24,0.781 10 false Telephone Antenna Cord Sub-assembly (Roof) 2.646,2.521 3.927,3.24 1.281,0.719 10 false No. 2 Antenna Cord Sub-assembly 5.792,1.563 6.115,1.844 0.323,0.281 10 false 1a 3.76,1.813 4.083,2.094 0.323,0.281 10 false C 3.729,1.583 4.052,1.865 0.323,0.281 10 false 3a 3.74,0.885 4.063,1.167 0.323,0.281 10 false 3 2.438,0.896 2.76,1.177 0.323,0.281 10 false 3 2.375,1.542 2.698,1.823 0.323,0.281 10 false 3a 1.052,1.552 1.375,1.833 0.323,0.281 10 false 4a 1.094,0.865 1.417,1.146 0.323,0.281 10 false 4 6.135,1.115 6.698,1.385 0.563,0.271 10 false TELM2 5.667,1.802 6.208,2 0.542,0.198 10 false H108 5.677,1.135 6.219,1.333 0.542,0.198 10 false H108 4.594,2.563 5.844,3.448 1.25,0.885 10 false Telephone Antenna Cord Sub-assembly (I/P) 3.76,1.125 4.083,1.406 0.323,0.281 10 false C 4.333,1.802 4.885,2.104 0.552,0.302 10 false H106 4.479,0.885 4.802,1.167 0.323,0.281 10 false 3 4.438,1.583 4.76,1.865 0.323,0.281 10 false 3a 4.781,1.125 5.344,1.396 0.563,0.271 10 false TELM1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEPHONE ANTENNA ASSEMBLY
2.INSPECT TELEPHONE ANTENNA ASSEMBLY
a.

Remove the telephone antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C15
1.979,1.448 2.229,1.417 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.271,1.333 2.583,1.531 0.313,0.198 10 false 4a
*a Telephone Antenna Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)

NG

REPLACE TELEPHONE ANTENNA ASSEMBLY

3.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)
E350951C14
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.271,1.563 1.688,1.521 true 2.01,3.99 2.542,4.156 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.073,1.479 1.385,1.677 0.313,0.198 10 false 4a 2.594,4.094 2.906,4.292 0.313,0.198 10 false 3a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.156,2.594 0.469,2.792 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Always Below 1 Ω
A-4a - B-3a Always Below 1 Ω
A-4 or B-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY (ROOF)

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
E467080C02
1.458,0.302 1.896,0.583 0.438,0.281 1.49,2.375 1.927,2.656 0.438,0.281 1.938,1.729 2.333,2 2.333,2 2.469,2 true 1.906,3.844 2.323,4.208 2.323,4.208 2.458,4.208 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.635,0.365 1.792,0.563 0.156,0.198 10 false B 1.677,2.427 2.073,2.635 0.396,0.208 10 false C 2.542,1.906 2.74,2.104 0.198,0.198 10 false 3a 2.531,4.104 2.729,4.302 0.198,0.198 10 false 3a 0.208,2.323 0.521,2.521 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly [Roof])
*b Front view of wire harness connector
(to Wire Harness)


a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly (roof).


b.

Disconnect the antenna connector from the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-3 - C-3 Always Below 1 Ω
B-3a - C-3a Always Below 1 Ω
B-3 or C-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEPHONE ANTENNA CORD SUB-ASSEMBLY [I/P])

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEPHONE ANTENNA CORD SUB-ASSEMBLY [I/P])
a.
E467082C04
0.354,0.667 0.854,0.979 0.5,0.313 0.385,2.427 0.885,2.74 0.5,0.313 2.563,1.625 2.344,1.625 2.344,1.625 1.885,1.146 true 2.385,3.281 2.167,3.281 2.167,3.281 1.708,2.802 true 1.125,3.281 1.323,3.281 1.323,3.281 1.604,2.74 true 0.552,0.729 0.865,0.927 0.313,0.198 10 false C 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.125,1.698 0.438,1.896 0.313,0.198 10 false *b 0.479,2.49 0.99,2.75 0.51,0.26 10 false H106 2.625,1.531 3.208,1.75 0.583,0.219 10 false 3a 2.458,3.177 3.042,3.396 0.583,0.219 10 false 3a 0.646,3.208 1.229,3.427 0.583,0.219 10 false TELM1
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly [I/P])


Disconnect the C connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the H106 telephone antenna cord sub-assembly (I/P) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-3 - H106-3 (TELM1) Always Below 1 Ω
C-3a - H106-3a Always Below 1 Ω
C-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)
E467083C03
1.5,0.427 1.896,0.708 0.396,0.281 1.531,2.604 2,2.906 0.469,0.302 1.896,3.75 2.365,4.156 2.365,4.156 2.542,4.156 true 1.521,2.104 1.677,2.104 1.677,2.104 1.833,1.625 true 1.021,3.5 1.177,3.5 1.177,3.5 1.688,3.677 true 1.875,1.448 2.615,1.031 2.615,1.031 2.792,1.031 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.323,2.01 1.635,2.208 0.313,0.198 10 false 3a 2.594,4.094 2.906,4.292 0.313,0.198 10 false 1a 1.542,0.49 2.167,0.75 0.625,0.26 10 false H106 1.573,2.656 2.063,2.854 0.49,0.198 10 false H108 0.156,2.594 0.469,2.792 0.313,0.198 10 false *b 0.51,3.427 1.083,3.698 0.573,0.271 10 false TELM2 2.833,0.958 3.406,1.229 0.573,0.271 10 false TELM1
*a Front view of wire harness connector
(to Wire Harness)
*b Front view of wire harness connector
(to Telephone Antenna Assembly)


a.

Disconnect the antenna connector from the wire harness.


b.

Disconnect the antenna connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H106-3 (TELM1) - H108-1 (TELM2) Always Below 1 Ω
H106-3a - H108-1a Always Below 1 Ω
H106-3 (TELM1) or H108-1 (TELM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY (I/P)

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT