Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P202D7A  Reductant Leakage Fluid Leak or Seal Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P202D7A Reductant Leakage Fluid Leak or Seal Failure Either of the following conditions is met:
·

When the rotation of the urea pump is equal to or greater than a fixed value, the pressure sensor value is below a fixed value.

·

When the level sensor value is equal to or greater than a fixed value and the injection accumulation amount is below a fixed value, the level sensor value decreases by a fixed value or greater compared to the last time the level sensor value was acquired.


(1 trip detection logic)
·

Urea tube with heater assembly

·

Urea injector set

·

Urea pump assembly (urea pump control ECU integrated urea pump)


Comes on DTC stored SAE Code: P202D

Related Data List
DTC No. Data List
P202D7A - (Refer to total remaining amount of urea solution on the multi-information display)

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P202D7A Start the engine with the vehicle on a level surface and idle it for approximately 15 minutes or more

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P202D7A)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P202D7A is output A
DTC P202D7A and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK AROUND BOTTOM OF VEHICLE

B

2.CHECK AROUND BOTTOM OF VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.



OK:

No urea solution leaks.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CHECK UREA INJECTOR OPERATION)

NG

REPAIR UREA SOLUTION LEAKS

3.PERFORM ACTIVE TEST USING GTS (CHECK UREA INJECTOR OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.


f.

Perform the Active Test.

HINT:

Perform the Reductant Purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



g.

After performing the Active Test, remove the urea injector set from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector set from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




h.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Injection Valve.


i.

Perform the Active Test and check for the sound of the urea injector set operating.

OK:

Sound of urea injector set operation can be heard (a ticking sound).



Result:
Proceed to
OK
NG



OK

4.CHECK INJECTION CONDITION OF UREA INJECTOR SET

NG

8.REPLACE UREA INJECTOR SET
4.CHECK INJECTION CONDITION OF UREA INJECTOR SET
a.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector set.


b.

Enter the following menus: Powertrain / Engine / Utility / Reductant Injection Valve Check.


c.

Execute the Reductant Injection Valve Check and check the injection condition of the urea injector set.

HINT:
·

This test performs operations from urea solution refueling up to injection.

·

The pressure inside the pipe may increase during urea solution refueling, intermittently opening the urea injector set and causing urea solution to leak out.

·

If the urea injector set becomes stuck open during urea solution refueling, once this test starts, intermittent injections will not occur and urea solution will leak out.

·

Urea solution is intermittently injected by the urea injector set.



OK:

3 streams of liquid are sprayed from the urea injector set.



Result:
Proceed to
OK
NG



OK

5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

7.CLEAN UREA INJECTOR SET
5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine with the vehicle on a level surface and idle it for approximately 15 minutes or more


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.CLEAN UREA INJECTOR SET
a.

Wash off any matter deposited by the urea solution.

NOTICE:
·

Do not damage the urea injector set when washing it.

·

Make sure to leave the connector connected when washing to prevent water from entering via the connector.

·

Sufficiently wipe the area so that no urea solution remains on the flange sealing surface.

·

After washing, check that 3 streams of liquid are sprayed from the urea injector set.




Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE UREA INJECTOR SET

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED