Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P208A19  Reductant Pump "A" Control Circuit High Circuit Current Above Threshold  P208A96  Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure  P20E900  Reductant Pressure Too High  


DESCRIPTION

Refer to DTC P203A96.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P203A96

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P208A19 Reductant Pump "A" Control Circuit High Circuit Current Above Threshold When power is supplied to the urea pump (during normal/reverse operation, power supplied to heater, position fixed), the pump current is equal to or greater than a fixed value.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P208D
P208A96 Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure When each pump status is "operating" (operation check, filling, pressure increase, pressure maintenance, line pressure relief), urea pump rotation malfunctions, pressure malfunctions, etc., are detected multiple times.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P208B
P20E900 Reductant Pressure Too High After filling the urea injector with urea solution from the urea pipe, the urea pressure is continuously higher than a fixed value.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P20E9

Related Data List
DTC No. Data List
P208A96
P208A19
P20E900
Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P208A19
P208A96
P20E900
Idle engine for 5 second

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P208A14, P208A19, P208A96 OR P20E900)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P208A19, P208A96 or P20E900 is output B
DTC P208A19, P208A96 or P20E900 and other DTCs are output* C


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




B

2.CHECK AROUND BOTTOM OF VEHICLE

C

2.CHECK AROUND BOTTOM OF VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.




b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

3.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
3.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and idle it for 5 seconds or more.


d.

Clear the DTCs.


e.

Turn the engine switch off for 30 seconds or more.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).


h.

Perform the Active Test.


i.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.


j.

Perform the Active Test.

HINT:

Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



k.

Enter the following menus: Powertrain / Engine / Trouble Codes.


l.

Read the DTCs.


Result:
Result Proceed to
No DTCs are output A
DTC P208A19, P208A96 or P20E900 is output B



A

4.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))

B

5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
4.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))
a.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.


b.

Execute "Reductant Filling (Pressure Keep)


c.

Check the Reductant Pressure.

OK:

450 to 550 kPa


HINT:

During a malfunction, pressure either does not increase, or increases to 800 kPa or higher and then stops.



Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and idle it for 5 seconds or more.


d.

Clear the DTCs.


e.

Turn the engine switch off for 30 seconds or more.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Start the engine and idle it for 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END