Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0441313 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM


E402556E42
1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false H93 5.74,2.635 6.969,3.021 1.229,0.385 10 false Radio and Display Receiver Assembly 0.917,3.073 1.375,3.302 0.458,0.229 10 false W7 1.042,2.385 2.469,2.875 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.115,0.833 3.573,1.063 0.458,0.229 10 false 14 3.115,1.844 3.573,2.073 0.458,0.229 10 false 13 1.021,2.24 2.448,2.729 1.427,0.49 10 false A

CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-22 (MIN-) - W7-13 (MCO-) Always Below 1 Ω
H93-25 (SNS2) - Body ground Always 10 kΩ or higher
H93-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.
E140936C37
1.021,1.344 1.302,0.75 1.302,0.75 1.479,0.75 true 0.885,1.365 0.74,0.76 0.74,0.76 0.594,0.76 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 1.531,0.635 2.167,0.885 0.635,0.25 10 false MCO- 0.135,0.667 0.646,0.844 0.51,0.177 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 13 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
a.
E355979C03
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 0.948,0.979 0.823,0.198 0.823,0.198 1,0.198 true 0.438,0.49 0.563,0.49 0.563,0.49 0.813,0.979 true 1.448,2.708 1.521,3.24 1.521,3.24 1.698,3.24 true 1.188,2.698 1,3.208 1,3.208 0.823,3.208 true 0.188,0.906 0.458,1.104 0.271,0.198 10 false W7 0.479,2.458 0.688,2.677 0.208,0.219 10 false A 1.063,0.115 1.542,0.333 0.479,0.219 10 false MCO- 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC- 0.042,0.417 0.521,0.635 0.479,0.219 10 false SNS2 0.427,3.135 0.906,3.354 0.479,0.219 10 false SNS2 0.177,1.885 0.385,2.104 0.208,0.219 10 false *b 0.083,0.063 0.292,0.281 0.208,0.219 10 false *a
*a Component without harness connected
(Map Light Assembly)
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-14 (SNS2) - A-1 (SNS2) Always Below 1 Ω
W7-13 (MCO-) - A-2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG