Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0441313 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

WIRING DIAGRAM

E370437E10
1,1.531 1.458,1.729 0.458,0.198 10 false H105 1,1.729 2.74,2.094 1.74,0.365 10 false Stereo Component Amplifier Assembly 4.969,0.781 5.208,0.99 0.24,0.208 10 false 14 2.052,0.771 2.281,0.958 0.229,0.188 10 false 24 1.521,0.927 1.979,1.125 0.458,0.198 10 false TMUT 5.292,0.896 5.781,1.094 0.49,0.198 10 false MUTE 4.99,1.531 5.448,1.729 0.458,0.198 10 false G333 5,1.719 6.938,1.958 1.938,0.24 10 false DCM (Telematics Transceiver)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DCM (TELEMATICS TRANSCEIVER)
a.
E427105C74
1.49,0.615 1.938,0.927 0.448,0.313 1.052,1.688 0.844,1.021 true 0.302,0.24 0.615,0.438 0.313,0.198 10 false *a 1.542,0.698 2.063,0.958 0.521,0.26 10 false G333 0.573,0.823 1.063,1.115 0.49,0.292 10 false MUTE
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G333-14 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the H105 stereo component amplifier assembly connector.


b.

Disconnect the G333 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H105-24 (TMUT) - G333-14 (MUTE) Always Below 1 Ω
H105-24 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the DCM (telematics transceiver) connector.


b.
E456934C03
1.479,0.719 1.969,1.01 0.49,0.292 2.469,2.135 2.646,2.635 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.531,2.667 2.958,2.823 0.427,0.156 10 false MUTE 1.573,0.781 2.208,1.125 0.635,0.344 10 false G333
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G333-14 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY