Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0441313 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

WIRING DIAGRAM

E451497E02
5.76,5.969 6.948,6.469 1.188,0.5 10 false Radio and Display Receiver Assembly 3.417,5.99 4.021,6.24 0.604,0.25 10 false H96 0.24,3.094 1.625,3.5 1.385,0.406 10 false Telephone Microphone Assembly 0.469,4.271 1.885,4.792 1.417,0.521 10 false Map Light Assembly 1.552,0.823 2.156,1.073 0.604,0.25 10 false 1 1.531,1.365 2.135,1.615 0.604,0.25 10 false 5 1.542,1.906 2.146,2.156 0.604,0.25 10 false 3 1.552,2.49 2.156,2.74 0.604,0.25 10 false 2 5.969,2.073 6.573,2.323 0.604,0.25 10 false MIN+ 5.563,0.938 6.167,1.188 0.604,0.25 10 false H93 5.625,0.729 6.229,0.979 0.604,0.25 10 false 25 5.635,1.865 6.24,2.115 0.604,0.25 10 false 21 5.625,2.406 6.229,2.656 0.604,0.25 10 false 22 5.625,2.969 6.229,3.219 0.604,0.25 10 false 24 5.615,4.917 6.219,5.167 0.604,0.25 10 false 26 5.948,4.573 6.552,4.823 0.604,0.25 10 false MCO+ 5.969,0.917 6.573,1.167 0.604,0.25 10 false SNS2 1.74,1.375 2.344,1.625 0.604,0.25 10 false MACC 1.781,0.813 2.385,1.063 0.604,0.25 10 false SNS2 1.76,1.927 2.365,2.177 0.604,0.25 10 false MCO+ 1.792,2.479 2.396,2.729 0.604,0.25 10 false MCO- 5.969,3.177 6.573,3.427 0.604,0.25 10 false SGND 5.615,5.458 6.219,5.708 0.604,0.25 10 false 24 5.625,4.354 6.229,4.604 0.604,0.25 10 false 25 5.958,2.635 6.563,2.885 0.604,0.25 10 false MIN- 5.573,4.563 6.177,4.813 0.604,0.25 10 false H94 3.406,6.167 4.521,6.427 1.115,0.26 10 false Navigation ECU 5.948,5.146 6.552,5.396 0.604,0.25 10 false MCO- 5.948,5.667 6.552,5.917 0.604,0.25 10 false SGND 3.969,4.563 4.573,4.813 0.604,0.25 10 false MIC+ 4.01,5.135 4.615,5.385 0.604,0.25 10 false MIC- 4.396,4.479 5,4.729 0.604,0.25 10 false 13 4.406,5.031 5.01,5.281 0.604,0.25 10 false 14 0.375,6.219 1.469,6.479 1.094,0.26 10 false *: Shielded 4.052,2.917 4.344,3.156 0.292,0.24 10 false * 5.969,1.521 6.573,1.771 0.604,0.25 10 false MACC 2.302,2.5 2.906,2.75 0.604,0.25 10 false 13 2.281,0.823 2.885,1.073 0.604,0.25 10 false 14 2.292,1.927 2.896,2.177 0.604,0.25 10 false 12 2.281,1.375 2.885,1.625 0.604,0.25 10 false 11 1.031,0.948 1.635,1.198 0.604,0.25 10 false SNS2 1.031,1.51 1.635,1.76 0.604,0.25 10 false MACC 1.104,2.052 1.708,2.302 0.604,0.25 10 false MIC+ 1.125,2.583 1.729,2.833 0.604,0.25 10 false MIC- 5.625,1.313 6.229,1.563 0.604,0.25 10 false 23 0.24,2.917 0.844,3.167 0.604,0.25 10 false A 5.583,1.5 6.188,1.75 0.604,0.25 10 false H93 5.583,2.073 6.188,2.323 0.604,0.25 10 false H93 5.583,2.615 6.188,2.865 0.604,0.25 10 false H93 5.573,3.177 6.177,3.427 0.604,0.25 10 false H93 5.573,5.135 6.177,5.385 0.604,0.25 10 false H94 5.563,5.677 6.167,5.927 0.604,0.25 10 false H94 4.875,5.385 5.167,5.625 0.292,0.24 10 false * 0.469,4.083 1.073,4.333 0.604,0.25 10 false W7

CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the H94 radio and display receiver assembly connector.


b.

Disconnect the H96 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H94-25 (MCO+) - H96-13 (MIC+) Always Below 1 Ω
H94-26 (MCO-) - H96-14 (MIC-) Always Below 1 Ω
H94-25 (MCO+) or H96-13 (MIC+) - Body ground Always 10 kΩ or higher
H94-26 (MCO-) or H96-14 (MIC-) - Body ground Always 10 kΩ or higher
H94-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)
a.
E368005C65
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 true 0.833,2.083 1.188,1.469 true 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.583,0.469 1.979,0.698 0.396,0.229 10 false H96 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU)


Check the output waveform.

i.

Disconnect the navigation ECU connector.


ii.

Turn the ignition switch to ACC.


iii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H96-13 (MIC+) - H96-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-23 (MACC) - W7-11 (MACC) Always Below 1 Ω
H93-21 (MIN+) - W7-12 (MCO+) Always Below 1 Ω
H93-22 (MIN-) - W7-13 (MCO-) Always Below 1 Ω
H93-25 (SNS2) or W7-14 (SNS2) - Body ground Always 10 kΩ or higher
H93-23 (MACC) or W7-11 (MACC) - Body ground Always 10 kΩ or higher
H93-21 (MIN+) or W7-12 (MCO+) - Body ground Always 10 kΩ or higher
H93-22 (MIN-) or W7-13 (MCO-) - Body ground Always 10 kΩ or higher
H93-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E446276C04
1.531,0.552 1.906,0.854 0.375,0.302 2.26,2.833 1.927,2.125 true 1.917,3.104 1.823,2.125 true 2.729,2.625 2.073,2.125 true 1.573,0.615 1.875,0.802 0.302,0.188 10 false H93 0.125,0.104 0.427,0.292 0.302,0.188 10 false *a 2.302,2.844 2.76,3.01 0.458,0.167 10 false MACC 1.781,3.135 2.24,3.302 0.458,0.167 10 false SGND 2.781,2.583 3.24,2.75 0.458,0.167 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-24 (SGND) - Body ground Always Below 1 Ω
H93-22 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H93-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

7.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER)

NG

7.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER)
a.
E446247C03
1.5,0.219 1.938,0.49 0.438,0.271 1.052,0.271 1.188,0.271 1.188,0.271 1.292,1.094 true 0.865,0.51 1,0.51 1,0.51 1.219,1.104 true 1.594,0.26 1.906,0.458 0.313,0.198 10 false W7 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.854,3.438 3.167,3.635 0.313,0.198 10 false GND 0.625,0.177 1.094,0.385 0.469,0.208 10 false MCO+ 0.458,0.417 0.927,0.625 0.469,0.208 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Check the output waveform.

i.

Remove the map light assembly with the connector(s) still connected.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


ii.

Connect an oscilloscope to terminals 12 (MCO+) and 13 (MCO-) of the W7 map light assembly connector.


iii.

Turn the ignition switch to ACC.


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal W7-12 (MCO+) - W7-13 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

NG

8.INSPECT MAP LIGHT ASSEMBLY
8.INSPECT MAP LIGHT ASSEMBLY
a.
E355979C06
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 1.229,0.958 1.875,0.438 1.875,0.438 2.052,0.438 true 0.948,0.979 0.823,0.198 0.823,0.198 1,0.198 true 2.26,2.688 2.417,3.01 2.417,3.01 2.573,3.01 true 1.74,2.698 2.125,3.198 2.125,3.198 2.302,3.198 true 0.438,0.49 0.563,0.49 0.563,0.49 0.813,0.979 true 1.083,0.979 1.563,0.219 1.563,0.219 1.74,0.219 true 1.448,2.708 1.521,3.24 1.521,3.24 1.698,3.24 true 1.188,2.698 1,3.208 1,3.208 0.823,3.208 true 0.177,0.906 0.49,1.115 0.313,0.208 10 false W7 0.49,2.458 0.698,2.677 0.208,0.219 10 false A 2.615,2.927 3.052,3.135 0.438,0.208 10 false MACC 2.104,0.365 2.542,0.573 0.438,0.208 10 false MACC 1.813,0.146 2.292,0.365 0.479,0.219 10 false MCO+ 1.063,0.115 1.542,0.333 0.479,0.219 10 false MCO- 2.344,3.115 2.823,3.333 0.479,0.219 10 false MIC+ 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC- 0.042,0.417 0.521,0.635 0.479,0.219 10 false SNS2 0.427,3.135 0.906,3.354 0.479,0.219 10 false SNS2 0.063,0.083 0.542,0.302 0.479,0.219 10 false *a 0.042,1.531 0.521,1.75 0.479,0.219 10 false *b
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-11 (MACC) - A-5 (MACC) Always Below 1 Ω
W7-12 (MCO+) - A-3 (MIC+) Always Below 1 Ω
W7-13 (MCO-) - A-2 (MIC-) Always Below 1 Ω
W7-14 (SNS2) - A-1 (SNS2) Always Below 1 Ω
W7-11 (MACC) - W7-12 (MCO+) Always 10 kΩ or higher
W7-11 (MACC) - W7-13 (MCO-) Always 10 kΩ or higher
W7-11 (MACC) - W7-14 (SNS2) Always 10 kΩ or higher
W7-12 (MCO+) - W7-13 (MCO-) Always 10 kΩ or higher
W7-12 (MCO+) - W7-14 (SNS2) Always 10 kΩ or higher
W7-13 (MCO-) - W7-14 (SNS2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG