Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › from 2021.06
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  B241A  Rear Height Control Sensor  B2416  Height Control Sensor  


DESCRIPTION

The No. 1 headlight ECU sub-assembly LH receives vehicle height signals from the suspension control ECU. The No. 1 headlight ECU sub-assembly LH outputs DTC B241A.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2416 Height Control Sensor Malfunction in suspension control ECU Air suspension system w/ Air Suspension System
B241A Rear Height Control Sensor Malfunction in suspension control ECU Air suspension system w/ Air Suspension System

This DTC is stored when the No. 1 headlight ECU sub-assembly LH detects a malfunction in the rear height control sensor sub-assembly RH power source circuit or rear height control sensor sub-assembly RH circuit. The No. 1 headlight ECU sub-assembly LH stores DTC B241A.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2416 Height Control Sensor Either of the following conditions is met:
·

Malfunction in rear height control sensor sub-assembly RH

·

Open or short in rear height control sensor sub-assembly RH circuit


·

Rear height control sensor sub-assembly RH

·

Harness or connector

·

No. 1 headlight ECU sub-assembly LH


w/o Air Suspension System
B241A Rear Height Control Sensor Either of the following conditions is met:
·

Malfunction in rear height control sensor sub-assembly RH

·

Open or short in rear height control sensor sub-assembly RH circuit


·

Rear height control sensor sub-assembly RH

·

Harness or connector

·

No. 1 headlight ECU sub-assembly LH


w/o Air Suspension System

WIRING DIAGRAM

w/ Air Suspension System:
E346695E08
4.531,1.563 7,1.979 2.469,0.417 10 false No. 1 Headlight ECU Sub-assembly LH 1.208,1.583 2.948,1.979 1.74,0.396 10 false Suspension Control ECU 0.729,2.208 2.469,2.604 1.74,0.396 10 false : CAN Communication Line

w/o Air Suspension System:
E370854E94
4.208,2.302 6.875,2.698 2.667,0.396 10 false No. 1 Headlight ECU Sub-assembly LH 4.198,2.156 4.729,2.427 0.531,0.271 10 false A130 2.854,1.51 3.146,1.76 0.292,0.25 10 false 3 2.854,1 3.146,1.25 0.292,0.25 10 false 2 2.854,0.49 3.146,0.74 0.292,0.25 10 false 1 4.958,0.302 5.25,0.552 0.292,0.25 10 false 5 V 2.448,0.552 2.917,0.865 0.469,0.313 10 false SHB 2.365,1.083 2.917,1.448 0.552,0.365 10 false SHRR 2.438,1.594 2.979,1.938 0.542,0.344 10 false SHG 0.667,2.125 3.573,2.344 2.906,0.219 10 false S3 4.094,1.5 4.385,1.75 0.292,0.25 10 false 15 4.354,1.5 5.031,1.802 0.677,0.302 10 false SGR 4.344,1 4.99,1.323 0.646,0.323 10 false SHRL 4.104,0.99 4.396,1.24 0.292,0.25 10 false 17 4.104,0.49 4.396,0.74 0.292,0.25 10 false 16 4.375,0.51 5.156,0.813 0.781,0.302 10 false SBR 0.646,2.323 3.552,2.542 2.906,0.219 10 false Rear Height Control Sensor Sub-assembly RH

CAUTION / NOTICE / HINT

NOTICE:
w/o Air Suspension System:
·

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION

·

If any of the following are performed, it is necessary to initialize the No. 1 headlight ECU sub-assembly LH.

-

Replacement of the rear height control sensor sub-assembly RH

-

Removal/installation of the rear height control sensor sub-assembly RH

-

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Air Suspension System A
w/o Air Suspension System B



A

2.CHECK FOR DTC

B

3.CHECK FOR DTC
2.CHECK FOR DTC

b.

Turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR

OK:

DTC B241A is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK FOR DTC

b.

Turning the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR

OK:

DTC B2416 and B241A are not output.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
a.

Remove the rear height control sensor sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH)
a.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


b.

Disconnect the S3 rear height control sensor sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A130-16 (SBR) - S3-1 (SHB) Always Below 1 Ω
A130-15 (SGR) - S3-3 (SHG) Always Below 1 Ω
A130-17 (SHRL) - S3-2 (SHRR) Always Below 1 Ω
A130-16 (SBR) or S3-1 (SHB) - Body ground Always 10 kΩ or higher
A130-15 (SGR) or S3-3 (SHG) - Body ground Always 10 kΩ or higher
A130-17 (SHRL) or S3-2 (SHRR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR