The No. 1 headlight ECU sub-assembly receives a signal from each headlight leveling motor using LIN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2424 | Headlight Leveling Motor LH Communication Malfunction | Either condition is met:
·
Malfunction in headlight leveling motor LH ·
Open or short in headlight leveling motor LH communication circuit |
·
Headlight leveling motor LH ·
Headlight unit LH ·
No. 1 headlight ECU sub-assembly LH |
- |
| B2425 | Headlight Beam Level Control Motor RH Lost Communication | Either condition is met:
·
Malfunction in headlight leveling motor RH ·
Open or short in headlight leveling motor RH communication circuit |
·
Headlight leveling motor RH ·
Headlight unit RH ·
Harness or connector ·
No. 1 headlight ECU sub-assembly RH ·
No. 1 headlight ECU sub-assembly LH |
- |
If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
DTC B2424 and B2425 are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2424 and B2425 are output) | B |
| NG (DTC B2424 is output) | C |
| NG (DTC B2425 is output) | D |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only DTC B2425 is output | A |
| DTC B2424 and B2425 are output | B |
A
B
Remove the No. 1 headlight ECU sub-assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Connect the A103 No. 1 headlight ECU sub-assembly RH connector.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only DTC B2425 is output | A |
| DTC B2424 and B2425 are output | B |
A
B
Disconnect the headlight leveling motor RH connector.
Connect the No. 1 headlight ECU sub-assembly RH connectors.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only DTC B2425 is output | A |
| DTC B2424 and B2425 are output | B |
A
B
Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.
Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A102-20 (LINL) or A103-20 (LINL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Connect the A130 No. 1 headlight ECU sub-assembly LH connector.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only DTC B2424 is output | A |
| DTC B2424 and B2425 are output | B |
A
B
Disconnect the headlight leveling motor LH connector.
Connect the No. 1 headlight ECU sub-assembly LH connectors.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only DTC B2424 is output | A |
| DTC B2424 and B2425 are output | B |
A
B
Remove the headlight unit LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY
| *a | Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH) |
*b | Front view of wire harness connector
(to Headlight Unit Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - E-1 | Always | Below 1 Ω |
| B-17 (ACTGI) - E-3 | Always | Below 1 Ω |
| C-13 (LINLI) - E-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Leveling Motor LH) |
Disconnect the headlight leveling motor LH connector.
Connect the No. 1 headlight ECU sub-assembly LH connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E-1 - E-3 | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 headlight ECU sub-assembly LH as a unit with the connectors still connected.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-13 (LINLI) - A103-20 (LINL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.
Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A130-20 (LINL) - A103-20 (LINL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight unit RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY
| *a | Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly RH) |
*b | Front view of wire harness connector
(to Headlight Unit Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - E-1 | Always | Below 1 Ω |
| B-17 (ACTGI) - E-3 | Always | Below 1 Ω |
| B-13 (LINLI) - E-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Leveling Motor RH) |
Disconnect the headlight leveling motor RH connector.
Connect the No. 1 headlight ECU sub-assembly RH connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E-1 - E-3 | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 headlight ECU sub-assembly RH as a unit with the connectors still connected.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-13 (LINLI) - A130-20 (LINL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG