Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20F400  Reductant Consumption Too Low  


DESCRIPTION

This DTC is stored when the urea solution injection amount is estimated from the speed of the urea pump assembly (urea pump control ECU integrated urea pump), and it is determined that the urea solution injection amount has dropped when the drop in the urea solution level is less than the threshold for the estimated injection amount.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P20F400 Reductant Consumption Too Low The drop in the urea solution level is at the threshold or lower for the urea injection amount estimated from the urea pump speed
(1 trip detection logic)
·

Urea injector set

·

Urea pump assembly (urea pump control ECU integrated urea pump)


Comes on DTC stored SAE Code: P20F4

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20F400 After warm-up, repeatedly accelerate from stopped (approximately 5 seconds) to 40 km/h (for approximately 20 minutes).
HINT:

If the vehicle is equipped with a Stop and Start System, stop functionality prior to driving.



CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

d.

Read the DTCs.

Result:
Result Proceed to
DTC P20F400 is output A
P20F400 and other DTCs are output B




A

2.CHECK UREA INJECTION PIPES (CHECK DEPOSIT)

B

GO TO DTC CHART

2.CHECK UREA INJECTION PIPES (CHECK DEPOSIT)
HINT:

If there are deposits around the urea injector, injection may be inhibited, reducing purification performance.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 456 16

d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Purge
50004 456 17

f.

Perform the Active Test.

HINT:

Perform the Reductant Purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



g.

After performing the Active Test, remove the urea injector set from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:

Do not disconnect the urea injector from the urea tube with heater assembly.



h.
A383896C02
2.125,1.229 2.385,0.74 2.385,0.74 2.552,0.74 false 0.969,2.802 1.313,3.021 0.344,0.219 11 false *a 2.583,0.667 2.927,0.885 0.344,0.219 11 false *1
*a Exhaust Pipe Connection Area to Check
*1 Front Exhaust Pipe Assembly


Check that there is no white matter deposited by urea solution on the connection area of the front exhaust pipe.

HINT:

After checking for deposits, use a cover, etc., to prevent foreign matter from entering the front exhaust pipe.



Result:
Result Proceed to
No white matter is deposited by urea solution on connection area of front exhaust pipe A
White matter is deposited by urea solution on connection area of front exhaust pipe B



A

3.PERFORM ACTIVE TEST USING GTS (UREA INJECTOR SET OPERATION CHECK)

B

11.REMOVE DEPOSIT
3.PERFORM ACTIVE TEST USING GTS (UREA INJECTOR SET OPERATION CHECK)
HINT:

If there is a malfunction in the urea injector set, NOx purification performance will be reduced.


a.

Use a cover, etc., to prevent foreign matter from entering the front exhaust pipe where the urea injector set was removed.


b.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Injection Valve.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Injection Valve
50004 456 13

c.

Perform the Active Test and check that operation sounds can be heard from the urea injector set.

OK:

Sound of urea injector set operation can be heard (a ticking sound).


HINT:

Even after checking is complete, do not install the urea injector removed from the front exhaust pipe yet.



Result:
Proceed to
OK
NG



OK

4.UREA INJECTOR INJECTION STATE CHECK

NG

10.REPLACE UREA INJECTOR SET
4.UREA INJECTOR INJECTION STATE CHECK
a.

Enter the following menus: Powertrain / Engine and Transmission / Utility / Reductant Injection Valve Check.

Powertrain > Engine and Transmission > Utility
Tester Display
Reductant Injection Valve Check
50005 456 4601

b.

Execute the Reductant Injection Valve Check and check the injection condition of the urea injector set.

HINT:
·

This test performs operations from urea solution refueling up to injection.

·

The pressure inside the pipe may increase during urea solution refueling, intermittently opening the urea injector set and causing urea solution to leak out.

·

If the urea injector set becomes stuck open during urea solution refueling, once this test starts, intermittent injections will not occur and urea solution will leak out.

·

Urea solution is intermittently injected by the urea injector set.



A362197C02
3.875,1.167 4.688,0.177 4.688,0.177 4.031,0.75 false 3.594,0.813 4.688,0.177 4.688,0.177 4.865,0.177 false 0.344,0.531 0.656,0.688 0.313,0.156 10 false *1 4.917,0.104 5.229,0.26 0.313,0.156 10 false *2 4.99,0.563 5.302,0.719 0.313,0.156 10 false *a 3.99,1.74 4.302,1.896 0.313,0.156 10 false *b
*1 Urea Injector Set *2 Spray Hole
*a Urea injector set normal *b Urea injector set abnormal


Result:
Result Proceed to
Urea injector set normal A
Urea injector set abnormal B


HINT:

Even after checking is complete, do not install the urea injector removed from the front exhaust pipe yet.



c.

Wash off any matter deposited by the urea solution.

NOTICE:
·

Do not damage the urea injector set when washing it.

·

Make sure to leave the connector connected when washing to prevent water from entering via the connector.

·

Sufficiently wipe the area so that no urea solution remains on the flange sealing surface.

·

After completing work, check that 3 streams of liquid are sprayed from the urea injector set.





A

5.CHECK UREA INJECTOR INJECTION VOLUME

B

10.REPLACE UREA INJECTOR SET
5.CHECK UREA INJECTOR INJECTION VOLUME
a.

Set the urea injector set to the graduated cylinder to measure the injection volume of the urea injector set.


b.

Enter the following menus: Powertrain / Engine and Transmission / Utility / Reductant Injection Valve Check.

Powertrain > Engine and Transmission > Utility
Tester Display
Reductant Injection Valve Check
50005 456 4601

c.
A449031C01
1.958,1.76 2.688,1.542 false 0.417,0.281 1.698,1.146 true 0.229,0.177 0.542,0.375 0.313,0.198 10 false *1 2.729,1.438 3.042,1.635 0.313,0.198 10 false *2
*1 Urea Injector Set
*2 Graduated Cylinder


Execute the Reductant Injection Valve Check and measure the amount of urea injected in 1 minute.

HINT:
·

This test performs operations from urea solution refueling up to injection.

·

The pressure inside the pipe may increase during urea solution refueling, intermittently opening the urea injector set and causing urea solution to leak out.

·

If the urea injector set becomes stuck open during urea solution refueling, once this test starts, intermittent injections will not occur and urea solution will leak out.

·

Urea solution is intermittently injected by the urea injector set.



Result:
Result Proceed to
1-minute injection volume is 13 cc or more A
1-minute injection volume is less than 13 cc B


HINT:

Even after checking is complete, do not install the urea injector removed from the front exhaust pipe yet.



d.

Wash off any matter deposited by the urea solution.

NOTICE:
·

Do not damage the urea injector set when washing it.

·

Make sure to leave the connector connected when washing to prevent water from entering via the connector.

·

Sufficiently wipe the area so that no urea solution remains on the flange sealing surface.

·

After completing work, check that 3 streams of liquid are sprayed from the urea injector set.





A

6.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)

B

10.REPLACE UREA INJECTOR SET
6.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge / Data List / Diesel Exhaust / Reductant Pressure.


f.

After executing the Active Test, check the Reductant Pressure.

Standard:

Approximately 0 kPa



g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.


h.

After executing the Active Test, check the Reductant Pressure.

HINT:

Perform the Active Test until the pressure stabilizes (may take from 5 to 60 seconds).


OK:

450 to 550 kPa



Result:
Proceed to
OK
NG



OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

8.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Warm up the engine.


e.

Repeatedly accelerate from stopped (approximately 5 seconds) to 40 km/h for approximately 20 minutes.


f.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

g.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Warm up the engine.


e.

Repeatedly accelerate from stopped (approximately 5 seconds) to 40 km/h for approximately 20 minutes.


f.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

g.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPLACE UREA INJECTOR SET

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REMOVE DEPOSIT
a.

Clean any deposits from communicating portions of the front exhaust pipe.

HINT:

After washing, make sure to wipe off the flange surface so that no urea solution remains.



Result:
Proceed to
NEXT



NEXT

3.PERFORM ACTIVE TEST USING GTS (UREA INJECTOR SET OPERATION CHECK)