2011-2013 Land Cruiser · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

NOTICE:
When using a vise, do not overtighten it.


1. INSTALL STEERING MAIN SHAFT ASSEMBLY (w/o Entry and Start System)
  1. Install the steering main shaft assembly to the steering column upper tube.

  1. C104470E02
    Using a snap ring expander, install a new shaft snap ring to the steering main shaft assembly.

    NOTICE:
    1. Make sure the steering main shaft snap ring is securely installed to the groove.
    2. Do not damage the steering main shaft assembly.


2. INSTALL NO. 1 TILT STEERING SUPPORT COLLAR (w/o Entry and Start System)

  1. C104850E01
    Install the 2 No. 1 tilt steering support collars to the steering lower column tube assembly.

    NOTICE:
    When installing the No. 1 tilt steering support collar, make sure that the cutout portion is aligned as shown in the illustration.


3. INSTALL STEERING COLUMN BRACKET SPACER (w/o Entry and Start System)

  1. C104853E01
    Clamp the steering column bracket spacer and steering lower column tube assembly in a vise between a cloth and aluminum plates, and install the steering column bracket spacer to the steering lower column tube assembly using the vise.

    NOTICE:
    When installing the steering column bracket spacer, make sure that it is positioned so that the inner diameter is as shown in the illustration.


4. INSTALL TELESCOPIC STEERING GUIDE (w/o Entry and Start System)

  1. C104854E06
    Align the 3 protrusions of the telescopic steering guide with the 3 holes of the steering lower column tube assembly and install the telescopic steering guide.


5. INSTALL STEERING LOWER COLUMN TUBE ASSEMBLY (w/o Entry and Start System)

  1. C214697E01
    Apply MP grease to the area of the steering main shaft assembly indicated by the arrow in the illustration.

  1. C248949
    Install the steering lower column tube assembly to the steering column upper tube.


6. INSTALL TILT STEERING SUPPORT (w/o Entry and Start System)

  1. C247264
    Install the tilt steering support with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


7. INSTALL NO. 1 STEERING COLUMN RING (w/o Entry and Start System)

  1. C214675E01
    Using a snap ring expander, install a new No. 1 steering column ring to the steering main shaft.

    NOTICE:
    1. Make sure the No. 1 steering column ring is securely installed to the groove.
    2. Do not damage the steering main shaft assembly.


8. INSTALL TILT STEERING PAWL ASSEMBLY (w/o Entry and Start System)

  1. C104475
    Install the tilt steering pawl assembly to the steering column upper tube.

    NOTICE:
    When installing the tilt steering pawl assembly, position the opening as shown in the illustration.


9. INSTALL BREAK AWAY BRACKET (w/o Entry and Start System)

  1. C248948
    Apply MP grease to the sliding areas of a new break away bracket and install it to the steering column upper tube.


10. INSTALL STEERING COLUMN TUBE STOPPER (w/o Entry and Start System)

  1. C248950E01
    Apply MP grease to the sliding surface of the steering column tube stopper (the one with the groove) and install it to the break away bracket.

    NOTICE:
    Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.

  1. C248951E01
    Apply MP grease to the sliding surface of the steering column tube stopper (the one without the groove) and install it to the break away bracket.

    NOTICE:
    Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.


11. INSTALL NO. 1 TILT LEVER LOCK BOLT (w/o Entry and Start System)

  1. C104479E01
    Apply MP grease to the sliding surface of the steering tilt lever and install it to the No. 1 tilt lever lock bolt.

  1. C248952
    Install the No. 1 tilt lever lock bolt to the break away bracket.

    NOTICE:
    1. Do not drop the steering column tube stopper.
    2. Pass the No. 1 tilt lever lock bolt through the hole of the tilt steering pawl assembly.

  1. C248953
    Apply MP grease to the sliding surface of the thrust needle roller bearing and install it to the No. 1 tilt lever lock bolt.

  1. Temporarily install the tilt steering rotor to the No. 1 tilt lever lock bolt with a new No. 1 tilt steering adjusting nut.

  1. C248954
    Using an 8 mm socket hexagon wrench, tighten the No. 1 tilt lever lock bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

    NOTICE:
    The tightening direction for the No. 1 tilt lever lock bolt is the tightening direction for bolts with a left-handed thread.


12. INSTALL NO. 1 TILT STEERING SUPPORT REINFORCEMENT (w/o Entry and Start System)

  1. C248955
    Install the No. 1 tilt steering support reinforcement to the steering tilt lever with the steering tilt lever bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    The tightening direction for the steering tilt lever bolt is the tightening direction for bolts with a left-handed thread.


13. TIGHTEN NO. 1 TILT STEERING ADJUSTING NUT (w/o Entry and Start System)

  1. C248956
    Lock the steering tilt lever.

  1. C248957E01
    Using an 8 mm socket hexagon wrench, hold the No. 1 tilt lever lock bolt in place and tighten the No. 1 tilt steering adjusting nut.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. C216017
    Using pliers, stake the No. 1 tilt steering adjusting nut as shown in the illustration.

    NOTICE:
    After staking the No. 1 tilt steering adjusting nut, make sure it is not loose.


14. INSTALL TILT STEERING JUMP UP SPRING (w/o Entry and Start System)

  1. C104486
    Using pliers, move the tilt steering jump up spring in the direction indicated by the arrow in the illustration to install it to the break away bracket.

    NOTICE:
    To avoid spatter, cover the area with a cloth.


15. INSTALL TILT LEVER RETURN SPRING (w/o Entry and Start System)

  1. C248939E01
    Using SST, install the tilt lever return spring to the break away bracket and steering tilt lever.
    SST
    09921-00010  

    NOTICE:
    1. To avoid spatter, cover the area with a cloth.
    2. Do not let the damper fall off of the tilt lever return spring.


16. INSTALL TILT STEERING SUPPORT BOND CABLE (w/o Entry and Start System)

  1. C246796
    Install the steering support bond cable to the steering column with the 2 screws.


17. INSTALL BREAK AWAY COLLAR SUB-ASSEMBLY (w/o Entry and Start System)

  1. C104462E02
    Install the 2 new break away collars and 2 new break away capsules to the break away bracket.

    NOTICE:
    Do not compress the disc spring portion of the break away collar.


18. INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

  1. C104552E01
    Attach the 2 claws to install the ignition or starter switch assembly to the steering column upper bracket assembly.


19. INSTALL UNLOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

  1. C104837E03
    Attach the 2 claws to install the unlock warning switch assembly to the steering column upper bracket assembly.

    HINT:
    Move the unlock warning switch assembly in the direction indicated by the arrow in the illustration to install it.


20. INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)
  1. Turn the ignition switch lock cylinder assembly to ACC.

  1. C214540E01
    Insert the ignition switch lock cylinder assembly into the steering column upper bracket assembly to install it.

  1. Check that the ignition switch lock cylinder assembly is securely fixed in place.


21. INSPECT STEERING LOCK OPERATION (w/o Entry and Start System)

  1. C103934
    Remove the key and check that the steering lock operates.

  1. C214539E01
    Insert the key, turn the ignition switch to ACC and check that the steering lock disengages.


22. INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Entry and Start System)

  1. C103936
    Install the steering column upper with switch bracket assembly and steering column upper clamp with 2 new steering lock set bolts, and tighten the bolts until the heads break off.


23. INSTALL TRANSPONDER KEY AMPLIFIER (w/o Entry and Start System)

  1. C103938E01
    Attach the 2 claws to install the transponder key amplifier to the steering column upper with switch bracket assembly.


24. INSTALL KEY INTERLOCK SOLENOID (for Automatic Transmission)

  1. G034357E01
    Install the key interlock solenoid to the steering column upper bracket with the 2 screws.


25. INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

C178341
  1. Temporarily install the steering lock actuator assembly with 2 new tapered-head bolts.

  1. Tighten the 2 tapered-head bolts until the bolt heads break off.

← INSPECTION (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →