P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
Refer to DTC P2120 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| P2121 |
Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic)
|
|
MONITOR DESCRIPTION
When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.FAIL-SAFE
The accelerator pedal position sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue to be driven. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.
WIRING DIAGRAM
Refer to DTC P2120 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- This DTC relates to the Accelerator Pedal Position (APP) sensor.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accelerator Position No.1 and Accelerator Position No.2.
Read the value displayed on the tester.
- Standard Voltage:
Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.0 V
Result Result
Proceed to
OK
A
NG
B
|
|
||||
| B | |
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the Accelerator Pedal Position (APP) sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
A31-6 (VPA) - A38-55 (VPA)
Always
Below 1 Ω
A31-5 (EPA) - A38-59 (EPA)
Always
Below 1 Ω
A31-4 (VCPA) - A38-57 (VCPA)
Always
Below 1 Ω
A31-3 (VPA2) - A38-56 (VPA2)
Always
Below 1 Ω
A31-2 (EPA2) - A38-60 (EPA2)
Always
Below 1 Ω
A31-1 (VCP2) - A38-58 (VCP2)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
A31-6 (VPA) - A52-55 (VPA)
Always
Below 1 Ω
A31-5 (EPA) - A52-59 (EPA)
Always
Below 1 Ω
A31-4 (VCPA) - A52-57 (VCPA)
Always
Below 1 Ω
A31-3 (VPA2) - A52-56 (VPA2)
Always
Below 1 Ω
A31-2 (EPA2) - A52-60 (EPA2)
Always
Below 1 Ω
A31-1 (VCP2) - A52-58 (VCP2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
A31-6 (VPA) or A38-55 (VPA) - Body ground
Always
10 kΩ or higher
A31-5 (EPA) or A38-59 (EPA) - Body ground
Always
10 kΩ or higher
A31-4 (VCPA) or A38-57 (VCPA) - Body ground
Always
10 kΩ or higher
A31-3 (VPA2) or A38-56 (VPA2) - Body ground
Always
10 kΩ or higher
A31-2 (EPA2) or A38-60 (EPA2) - Body ground
Always
10 kΩ or higher
A31-1 (VCP2) or A38-58 (VCP2) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
A31-6 (VPA) or A52-55 (VPA) - Body ground
Always
10 kΩ or higher
A31-5 (EPA) or A52-59 (EPA) - Body ground
Always
10 kΩ or higher
A31-4 (VCPA) or A52-57 (VCPA) - Body ground
Always
10 kΩ or higher
A31-3 (VPA2) or A52-56 (VPA2) - Body ground
Always
10 kΩ or higher
A31-2 (EPA2) or A52-60 (EPA2) - Body ground
Always
10 kΩ or higher
A31-1 (VCP2) or A52-58 (VCP2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P2121
A
No output
B
|
|
||||
| A | ||
| ||



