2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Injector (port)
    Injection period of the No. 1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    2.0 to 4.0 ms: idling
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 5 to 15°: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 25%: Idling
    2. 12 to 26%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) meter/
    Min.: 0 g/sec., Max.: 655 g/sec.
    4.0 to 8.0 g/sec.: Idling
    If the value is approximately 0.0 g/sec.:
    1. The mass air flow meter power source circuit is open or shorted.
    2. The VG circuit is open or shorted.
    If the value is 160.0 g/sec. or more:
    1. The E2G circuit is open.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 750 rpm: Idling
    -
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    The speed indicated on the speedometer.
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    80 to 100°C (176 to 212°F): After warming up
    If the value is -40°C (-40°F), the sensor circuit is open.
    If the value is 140°C (284°F), the sensor circuit is shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If the value is -40°C (-40°F), the sensor circuit is open.
    If the value is 140°C (284°F), the sensor circuit is shorted.
    2nd Air System Status
    Secondary air system status/
    ON or OFF
    ON: Secondary air system operation
    -
    Air-Fuel Ratio
    Air fuel ratio:
    Min.: 0, Max.: 1.999
    0.8 to 1.2: During idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -50, Max.: 350
    Idling: -40 to 0%
    Service data.
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 102.4%
    0 to 100%: Idling
    -
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    The order signal from the ECM.
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -64 CA, Max.: 1984 CA
    0 to 22° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -64 CA, Max.: 1984 CA
    -22 to 0° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Clutch Current
    Clutch current/
    Min.: 0 A, Max.: 2.49 A
    -
    -
    Accelerator Position No.1
    Absolute Accelerator Pedal Position (APP) No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: accelerator pedal is released
    54 to 86%: accelerator pedal is fully depressed
    -
    Accelerator Position No.2
    Absolute APP No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: accelerator pedal is released
    66 to 98%: accelerator pedal is fully depressed
    -
    Accelerator Position No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    The ETCS freeze data.
    Accelerator Position No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    The ETCS freeze data.
    Accelerator Position No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 5 V
    0.5 to 1.1 V: accelerator pedal is released
    2.6 to 4.5 V: accelerator pedal is fully depressed
    -
    Accelerator Position No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 5 V
    1.2 to 2.0 V: accelerator pedal is released
    3.4 to 5.3 V: accelerator pedal is fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)
    0.4 to 0.8 V
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No. 1 (AD)/
    Min.: 0, Max.: 4.98 V
    -
    The ETCS service data.
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0, Max.: 124.512
    -
    The ETCS service data.
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0, Max.: 124.512
    -
    The ETCS service data.
    Fail Safe Drive
    Whether or not fail-safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail-safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    ST1
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    System Guard
    System guard/
    ON or OFF
    -
    The ETCS service data.
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    The ETCS service data.
    Throttle Position
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 24%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    -
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 5 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    10 to 18%: Idling
    The calculated value based on VTA1.
    Throttle Sensor Position #2
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    -
    The calculated value based on VTA2.
    Throttle Position No.1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.9 V
    -
    The ETCS freeze data.
    Throttle Position No.2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.9 V
    -
    The ETCS freeze data.
    Throttle Position No.1
    Throttle position No. 1/
    Min.: 0 V, Max.: 5 V
    1. 0.5 to 1.2 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully open
    -
    Throttle Position No.2
    Throttle position No. 2/
    Min.: 0 V, Max.: 5 V
    1. 2.0 to 2.9 V: Throttle fully closed
    2. 4.6 to 5.5 V: Throttle fully open
    -
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    The ETCS service data.
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 0.9 V
    The ETCS service data.
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.98 V
    2.2 to 2.6 V
    The ETCS service data.
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No. 1 (AD)/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 0.9 V
    The ETCS service data.
    Throttle Motor
    Whether or not throttle actuator control permitted/
    ON or OFF
    ON: Idling
    Read the value with the engine switch on (IG) (do not the start engine).
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 80 A
    0 to 3.0 A: Idling
    -
    Throttle Motor
    Throttle actuator/
    Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    -
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.92 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio/
    Min.: 0%, Max.: 100%
    0 to 40%: During idling
    When the accelerator pedal is depressed, the duty ratio increases.
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio/
    Min.: 0%, Max.: 100%
    0 to 40%: During idling
    When the accelerator pedal is released quickly, the duty ratio increases.
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 100%
    -
    The ETCS service data.
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close)/
    Min.: 0%, Max.: 100%
    -
    The ETCS service data.
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving, 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S B2 S2
    Heated oxygen sensor output voltage for bank 2 sensor 2/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving, 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS B1 S1
    Air fuel ratio sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS B2 S1
    Air fuel ratio sensor output voltage for bank 2 sensor 1/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS B2 S1
    Air fuel ratio sensor current for bank 2 sensor 1/
    Min.: 128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    Total FT #1
    Total fuel trim of bank 1
    Average value for fuel trim system of bank 1/
    Min.: -0.5 V, Max.: 1496 V
    -0.2 to 0.2 V: Idling
    -
    Total FT #2
    Total fuel trim of bank 2
    Average value for fuel trim system of bank 2/
    Min.: -0.5 V, Max.: 1496 V
    -0.2 to 0.2 V: Idling
    -
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value.
    Short FT #2
    Short-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #2
    Long-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value.
    Fuel System Status (Bank1)
    Fuel system status (bank 1)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
    Fuel System Status (Bank2)
    Fuel system status (bank 2)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
    O2 FT B1 S2
    Short-term fuel trim associated with the bank 1 sensor 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    The same as Short FT #1.
    O2 FT B2 S2
    Short-term fuel trim associated with the bank 2 sensor 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    The same as Short FT #1.
    AF FT B1 S1
    Short-term fuel trim associated with the bank 1 sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Value equal to 1 = Stoichiometric air-fuel ratio
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AFS B1 S1
    Air fuel ratio sensor current bank 1 sensor 1/
    Min.: 128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    AF FT B2 S1
    Short-term fuel trim associated with the bank 2 sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Value equal to 1 = Stoichiometric air-fuel ratio
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    Catalyst Temp (B1 S1)
    Catalyst temperature (bank 1, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp (B2 S1)
    Catalyst temperature (bank 2, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp (B1 S2)
    Catalyst temperature (bank 1, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp (B2 S2)
    Catalyst temperature (bank 2, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    Close to ambient air temperature
    Service data.
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 140°C
    Close to ambient air temperature
    Service data.
    Injection Volum (Cylinder1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.048 ml
    0 to 0.5 ml
    The quantity of fuel injection volume for 10 times.
    Air pump pressure (absolute)
    Air pump pressure (absolute)/
    Min.: 0 kPa, Max.: 320 kPa
    Atmospheric pressure +1 kPa or more: Air pump on, air switching valve open
    Close to atmospheric pressure: Air pump off, air switching valve close
    Refer to DTC P2431 (Click here).
    Air Pump Pulsation Pressure
    Air pump pulsation pressure/
    Min.: 0 kPa, Max.: 639.9 kPa
    -
    The cumulative pulsation pressure calculated by the ECM.
    Power Steering Pressure
    Power steering oil pressure/
    Min.: -1.897 MPa, Max.: 12.799 MPa
    -
    -
    ACC Relay
    Acc relay status/
    ON or OFF
    ON: Cranking
    -
    Starter Relay
    Starter relay status/
    ON or OFF
    ON: Cranking
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Starter Control
    Starter switch status/
    ON or OFF
    ON: Cranking
    -
    Power Steering Switch
    Power steering switch status/
    ON or OFF
    ON: Power steering operation
    -
    Power Steering Signal
    Power steering signal (history)/
    ON or OFF
    ON: When steering wheel first turned after battery terminals connected
    This signal status is usually ON until the cables are disconnected from the battery terminals.
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    ON: P or N position
    -
    Electrical Load Signal
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger turned on
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power inputted/
    ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage/
    Min.: 0, Max.: 19.92
    10 to 15 V: Idling
    The ETCS service data.
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65535 V
    11 to 14 V: Idling
    -
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    The ETCS service data.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 150 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Secondary Air Control VSV
    Secondary air injection system status
    ON: Secondary air injection system operation
    -
    ACIS VSV
    VSV status for ACIS control/
    ON or OFF
    -
    The Active Test support data.
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    The Active Test support data.
    VVT Control Status (Bank2)
    VVT control status (bank 2)/
    ON or OFF
    -
    The Active Test support data.
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    The Active Test support data.
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    The Active Test support data.
    VVT Control Status (Bank1)
    Variable valve timing (VVT) control status (bank 1)/
    ON or OFF
    -
    The Active Test support data.
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    The Active Test support data.
    AI Test
    AI Test status/
    READY or NOT RDY
    -
    The Active Test support data.
    Engine Speed of Cyl #1
    Engine speed during No. 1 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Cylinder #1 injector fuel cut is performed using Active Test
    Engine Speed of Cyl #2
    Engine speed during No. 2 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #2 fuel cut is performed using Active Test
    Engine Speed of Cyl #3
    Engine speed during No. 3 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #3 fuel cut is performed using Active Test
    Engine Speed of Cyl #4
    Engine speed during No. 4 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #4 fuel cut is performed using Active Test
    Engine Speed of Cyl #5
    Engine speed during No. 5 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #5 fuel cut is performed using Active Test
    Engine Speed of Cyl #6
    Engine speed during No. 6 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #6 fuel cut is performed using Active Test
    Engine Speed of Cyl #7
    Engine speed during No. 7 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #7 fuel cut is performed using Active Test
    Engine Speed of Cyl #8
    Engine speed during No. 8 cylinder fuel cut/
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Control the Cylinder #8 fuel cut is performed using Active Test
    VVT Aim Angle (Bank1)*1
    VVT aim angle (bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    The VVT duty signal value during the intrusive operation.
    VVT Change Angle (Bank1)*1
    VVT change angle (bank 1)/
    Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    The displacement angle during the intrusive operation.
    VVT OCV Duty (Bank1)*1
    VVT OCV operation duty (bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    The requested duty value for the intrusive operation.
    VVT Aim Angle (Bank2)*1
    VVT aim angle (bank 2)/
    Min.: 0%, Max.: 100%
    0%: Idling
    The VVT duty signal value during the intrusive operation.
    VVT Change Angle (Bank2)*1
    VVT change angle (bank 2)/
    Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    The displacement angle during the intrusive operation.
    VVT OCV Duty (Bank2)*1
    VVT OCV operation duty (bank 2)/
    Min.: 0%, Max.: 100%
    0%: Idling
    The requested duty value for the intrusive operation.
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operation
    The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
    Ignition
    Ignition counter/
    Min.: 0, Max.: 800
    0 to 800
    -
    Cylinder #1 Misfire Count
    to
    Cylinder #8 Misfire Count
    Misfire count of the cylinder 1 to 8/
    Min.: 0, Max.: 255
    0%
    This item is displayed only when idling the engine.
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 35
    -
    Multi Cylinders Misfire Count
    Multiple cylinder misfire count/
    Min.: 0 Max.:65535
    0 to 65535
    -
    Misfire RPM
    Engine speed for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -100%, Max.: 99.22%
    -100 to 99.2%
    The misfire detecting margin.
    # Codes
    Number of codes/
    Min.: 0, Max.: 255
    -
    The number of stored DTCs.
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to the Check Mode Procedure (Click here).
    AS Test
    Check mode result for secondary air injection system/
    0: Compl, 1: Incmpl
    -
    -
    Misfire Test
    Check mode result for misfire monitor/
    0: Compl, 1: Incmpl
    -
    -
    OXS2 Test
    Check mode result for heated oxygen sensor (bank 2)/
    0: Compl, 1: Incmpl
    -
    -
    OXS1 Test
    Check mode result for heated oxygen sensor (bank 1)/
    0: Compl, 1: Incmpl
    -
    -
    A/F Test Results (Bank2)
    Check mode result for air fuel ratio sensor (bank 2)/
    0: Compl, 1: Incmpl
    -
    -
    A/F Test Results (Bank1)
    Check mode result for air fuel ratio sensor (bank 1)/
    0: Compl, 1: Incmpl
    -
    -
    MIL
    MIL status/
    ON or OFF
    ON: MIL on
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 minute, Max.: 65535 minutes
    Equivalent to running time after MIL is on
    -
    Engine Run Time
    Engine run time/
    Min.: 0 seconds, Max.: 65535 seconds
    Time after engine start
    Service data.
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes, Max.: 65535 minutes
    Equivalent to time after DTCs are cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs are cleared
    -
    Warmup Cycle Cleard DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    The number of warm-up cycles after the DTC is cleared.
    OBD Requirements
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Emission related DTCs
    -
    The number of emission related DTCs.
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR Monitor
    EGR monitor/
    Not Avl or Avail
    -
    -
    EGR Monitor
    EGR monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd AIR MON
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Model Code
    Model code
    -
    Identifying the model code:
    UZJ2##
    Engine Type
    Engine type
    -
    Identifying the engine type:
    2UZFE
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying the cylinder number:
    8
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    ECT (5AT)
    Destination
    Destination
    -
    Identifying the destination:
    W
    Model Year
    Model year/
    Min.: 0, Max.: 255
    -
    Identifying the model year:
    200#
    System Identification
    System identification
    -
    Identifying the engine system:
    Gasoline (gasoline engine)

HINT:
  1. Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in N or P, and the A/C switch is off and all accessory switches are off.
  2. *1: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2). For other Active Tests, the Data List value will be 0.


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12% and 25%
    1. All the injectors are tested at the same time.
    2. Perform the test at less than 3000 rpm.
    3. The injection volume can be changed in 1% graduations within the control range.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Lower by -12.5% or increase 25%
    1. Perform the test at less than 3000 rpm.
    2. Control the Injection Volume for A/F Sensor enables the checking and graphing of the A/F (Air-Fuel ratio) sensor voltage outputs.
    3. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S.
    Activate the VSV for Secondary Air Control
    Activate the secondary air system
    ON/OFF
    1. Do not perform the test for 5 seconds or more.
    2. After the test, do not perform the test again for 30 seconds.
    Activate the VSV for Intake Control
    Activate VSV for intake control
    ON/OFF
    -
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    -
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    -
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Activate the Starter Relay
    Activate the starter relay
    ON/OFF
    The engine is stopped.
    Activate the ACC Cut Relay
    Activate the ACC CUT relay
    ON/OFF
    The engine is stopped.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    ON: throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. The engine switch is on (IG).
    2. The engine does not start.
    3. The accelerator pedal is fully depressed (APP: 58 degrees or more).
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    ON: throttle valve opens fast
    The same as above.
    Control the VVT Linear (Bank1)
    Control Variable Valve Timing (VVT) [bank 1]
    -128 to 127%: This value added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. The engine stalls or idles roughly when the VVT actuator is operated by 100%.
    2. The test is possible during idle.
    Control the VVT System (Bank1)
    Turn on and off Camshaft Oil Control Valve (OCV)
    ON/OFF
    1. The engine stalls or idles roughly when the OCV is turned on.
    2. The engine runs or idles normally when the OCV is off.
    Control the VVT Linear (Bank2)
    Control Variable Valve Timing (VVT) [bank 2]
    -128 to 127%: This value added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. The engine stalls or idles roughly when the VVT actuator is operated by 100%.
    2. The test is possible during idle.
    Control the VVT System (Bank2)
    Turn on and off Camshaft Oil Control Valve (OCV)
    ON/OFF
    1. The engine stalls or idles roughly when the OCV is turned on.
    2. The engine runs or idles normally when the OCV is off.
    Control the Cylinder#1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#7 Fuel Cut
    Cylinder #7 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the Cylinder#8 Fuel Cut
    Cylinder #8 injector fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    The test is possible while the vehicle is stopped and the engine is idling.*
    Check the Cylinder Compression*1
    Check the cylinder compression pressure
    ON/OFF
    The fuel injection and ignition stop in all cylinders.

    NOTICE:
    *1: If the display of the Prohibit the Catalyst OT Misfire prevent F/C item of the Data List is Not Avl, perform this Active Test with the vehicle stopped and the engine idling. If the display of the Prohibit the Catalyst OT Misfire prevent F/C item of the Data List is Avail, perform this Active Test as described below.
    1. Stop the engine and turn the engine switch on (IG) to turn Control the Cylinder#1 Fuel Cut (to Control the Cylinder#8 Fuel Cut) ON.
    2. Start the engine.

    HINT:
    *: When cranking the engine, the Active Test measures the speed of each cylinder.
    In this Active Test, the fuel of all cylinders is cut, and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.
    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the engine switch on (IG) and turn the intelligent tester on.
    5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    6. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, the Active Test Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder engine speed measurement will enter standby.

    7. Fully open the throttle.
    8. Crank the engine for about 10 seconds.
    9. Monitor the engine speed (Engine Speed of Cyl #1 to #8) displayed on the intelligent tester.

      HINT:
      At first, the intelligent tester display will show each cylinder engine speed measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    NOTICE:
    1. When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.
    2. If the Check the Cylinder Compression test needs to be performed after it is turned on and performed once, press Exit to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
    3. Use a fully-charged battery.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the intelligent tester.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Secondary Air Injection Check
    (Automatic Mode)
    Perform secondary air injection system operation automatically
    With warm engine, engine switch turned off once
    1. If no DTCs in Pending after performing this test, system functioning normally
    2. Refer to inspection procedure for secondary air injection system DTCs
    3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with engine switch turned on (IG) or engine running
    4. Turn engine switch off when System Check finished
    Secondary Air Injection Check
    (Manual Mode)
    Perform 8 operations in order to operate air injection system monitor manually
    With warm engine, engine switch turned off once
    1. Used to detect malfunctioning parts
    2. Refer to inspection procedure for secondary air injection system DTCs
    3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with engine switch turned on (IG) or engine running
    4. Turn engine switch off when System Check finishes

← FAIL-SAFE CHART (Sep 2011 – Dec 2011)DIAGNOSTIC TROUBLE CODE CHART (Sep 2011 – Dec 2011) →