2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The diagnostic trouble code (DTC) P2431 indicates that the pressure sensor of the secondary air injection (AIR) system malfunctions. The engine control module (ECM) monitors the sensor value to detect the malfunction. If the sensor value reaches the criteria (below 45 kPa or higher than 135 kPa), the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The DTC P2432 and P2433 indicate an open or short circuit in the pressure sensor circuit. The ECM monitors the pressure sensor voltage to detect the open or short circuit. If the voltage reaches the criteria (below 0.1 V or higher than 4.8 V), the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The pressure sensor detects the air pressure via a piezo element. The ECM applies 5 volts to the sensor, and it is varied with the air pressure. When the pressure is high, the voltage is high. When the pressure is low, the voltage is low.
The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.
A182943E01
DTC Code
DTC Detection Condition
Trouble Area
P2431
The pressure sensor indicates below 45 kPa (338 mmHg) or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
  1. Pressure sensor circuit
  2. Pressure sensor
  3. ECM
P2432
The pressure sensor voltage is below 0.1 V (1 trip detection logic).
  1. Pressure sensor circuit
  2. Pressure sensor
  3. ECM
P2433
The pressure sensor voltage is higher than 4.8 V (1 trip detection logic).
  1. Pressure sensor circuit
  2. Pressure sensor
  3. ECM

WIRING DIAGRAM

A182502E01
A182502E02

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.


1. CHECK HARNESS AND CONNECTOR (AIR PRESSURE SENSOR - ECM)
A182503E01
  1. Disconnect the air pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C45-66 (VC) - D9-3 (VC)
    Always
    Below 1 Ω
    A38-54 (AIP) - D9-2 (AIP)
    Always
    Below 1 Ω
    C45-97 (ETHW) - D9-3 (ETHW)
    Always
    Below 1 Ω
    C45-66 (VC) or D9-3 (VC) - body ground
    Always
    10 kΩ or higher
    A38-54 (AIP) or D9-2 (AIP) (EPA) - body ground
    Always
    10 kΩ or higher
    C45-97 (ETHW) or D9-3 (ETHW) - body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C46-66 (VC) - D9-3 (VC)
    Always
    Below 1 Ω
    A52-54 (AIP) - D9-2 (AIP)
    Always
    Below 1 Ω
    C46-97 (ETHW) - D9-3 (ETHW)
    Always
    Below 1 Ω
    C46-66 (VC) or D9-3 (VC) - body ground
    Always
    10 kΩ or higher
    A52-54 (AIP) or D9-2 (AIP) (EPA) - body ground
    Always
    10 kΩ or higher
    C46-97 (ETHW) or D9-3 (ETHW) - body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

  1. A180778E01
    Remove the intake manifold (Click here).

  1. Disconnect the air pressure sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D9-3 (VC) - D9-1 (VC)
    Engine switch on (IG)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


3. REPLACE AIR PRESSURE SENSOR
  1. Replace the air pressure sensor (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Warm-up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Automatic Mode).

  1. Perform the Active Test and check the pending DTC.

    Result 
    Result
    Proceed to
    P2430, P2431, P2432, and/or P2433 is output
    A
    No DTC is output
    B



NG
REPLACE ECM (Click here)
OK

END


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ 9 more codes) (Sep 2011 – Dec 2011)P2444 Secondary Air Injection System Pump Stuck On Bank1 (+ P2445) (Sep 2011 – Dec 2011) →