2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with a heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. below 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.
A115539E07
DTC Code
DTC Detection Condition
Trouble Area
P0136
P0156
  1. Abnormal voltage output:
    During active air-fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    1. (a) The Heated Oxygen (HO2) sensor voltage does not decrease to below 0.21 V.
    1. (b) The HO2 sensor voltage does not increase to higher than 0.59 V.
  1. Open or short in HO2 sensor (for bank 1, 2) circuit
  2. HO2 sensor (for bank 1, 2)
  3. HO2 sensor heater (for bank 1, 2)
  4. Air-Fuel Ratio (A/F) sensor (for bank 1, 2)
  5. Integration relay
  6. Gas leakage from exhaust system
P0137
P0157
  1. Low voltage (open):
    During active air-fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    1. (a) The HO2 sensor voltage output is below 0.21 V.
    1. (b) The target air-fuel ratio is rich.
  1. Open in HO2 sensor (for bank 1, 2) circuit
  2. HO2 sensor (for bank 1, 2)
  3. HO2 sensor heater (for bank 1, 2)
  4. Integration relay
  5. Gas leakage from exhaust system
P0138
P0158
  1. High voltage (short):
    During active air-fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    1. (a) The HO2 sensor voltage output is higher than 0.59 V.
    1. (b) The target air-fuel ratio is lean.
  1. Short in HO2 sensor (for bank 1, 2) circuit
  2. HO2 sensor (for bank 1, 2)
  3. ECM internal circuit malfunction
  4. Air-Fuel Ratio (A/F) sensor (for bank 1, 2)

MONITOR DESCRIPTION

  1. Active Air-Fuel Ratio Control
    The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
    Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.
  1. Abnormal Voltage Output of HO2 Sensor (DTC P0136 and P0156)
    While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to below 0.21 V and does not increase to higher than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.
    A115540E09
  1. Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157 or P0138 and P0158)
    During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.
    While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is 0.59 V or higher (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and stores DTC P0138 or P0158.

    HINT:
    DTC P0138 or P0158 is also stored if the HO2 sensor voltage output is higher than 1.2 V for 10 seconds or more.

    *: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (Click here).
    A115541E12

WIRING DIAGRAM

A182258E01

CONFIRMATION DRIVING PATTERN

A166582E01
  1. Connect the intelligent tester to the DLC3.
  2. Turn the engine switch on (IG).
  3. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [A].
  4. Drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes or more [B].
  5. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times [C].
  6. Turn the tester on.
  7. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  8. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
  9. Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern by accelerating and decelerating the vehicle.

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1 or AFS B2 S1
(A/F)
+25%
Rich
Below 3.0 V
AFS B1 S1 or AFS B2 S1
(A/F)
-12.5%
Lean
Higher than 3.35 V
O2S B1 S2 or O2S B2 S2
(HO2)
+25%
Rich
Higher than 0.55 V
O2S B1 S2 or O2S B2 S2
(HO2)
-12.5%
Lean
Below 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E02
A150787E01
A150788E04
-
2
A150787E01
A150790E01
A150787E01
A150788E04
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E02
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be stored.
  4. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be stored.


1. READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0138 or P0158 is output
    A
    P0137 or P0157 is output
    B
    P0136 or P0156 is output
    C



B
Go to step 8

C
Go to step 6
A


2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Result 
    Result
    Proceed to
    Higher than 1.2 V
    A
    Below 1.0 V
    B



OK
Go to step 5

NG
Go to step 3
3. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A180104E02
  1. Disconnect the Heated Oxygen (HO2) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
A136305E46
  1. Turn the engine switch off and wait for 5 minutes.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C45-45 (HT1B) - C45-114 (OX1B)
    Always
    10 kΩ or higher
    C45-44 (HT2B) - C45-112 (OX2B)
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C46-45 (HT1B) - C46-114 (OX1B)
    Always
    10 kΩ or higher
    C46-44 (HT2B) - C46-112 (OX2B)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK AIR FUEL RATIO SENSOR CURRENT
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1 or AFS B2 S1.

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more.Perform this 3 times.

    HINT:
    If the tester shows Utility / Monitor Status / O2 Sensor / Incomplete again, increase the vehicle speed and use second gear to decelerate the vehicle.

  1. Read the value.

    Standard current:
    Below 3.0 mA

    A166581E03



OK
Go to step 12

NG
Go to step 14
6. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Read the output voltage of the HO2 sensor when the engine speed is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4000 rpm 3 times using the accelerator pedal.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.5 V or higher.



NG
Go to step 8
OK


7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
A121606E03
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
  2. The A/F sensor is displayed as AFS B1 S1 or AFS B2 S1, and the HO2 sensor is displayed as O2S B1 S2 or O2S B2 S2, on the intelligent tester.

    Result:
    Tester Display (Sensor)
    Voltage Variation
    Proceed to
    AFS B1 S1 (A/F)
    AFS B2 S1 (A/F)
    Alternates between higher than and below 3.3 V
    OK
    Remains at higher than 3.3 V
    NG
    Remains at below 3.3 V
    NG

    HINT:
    A normal HO2 sensor voltage (O2S B1 S2 or O2S B2 S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either below or higher than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.



NG
Go to step 14
OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO AND REPAIR CAUSE (INJECTOR, FUEL PRESSURE, GAS LEAKAGE FROM EXHAUST SYSTEM, ETC.)

8. CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leakage from the exhaust manifold and pipe.

    OK:
    No exhaust gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


9. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A180104E02
  1. Disconnect the Heated Oxygen (HO2) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E1)
    Always
    10 kΩ or higher
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


10. INSPECT INTEGRATION RELAY (EFI RELAY)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI MAIN fuse.

    1. Remove the EFI MAIN fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI MAIN fuse.

  1. Inspect the EFI relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      When no battery voltage applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      When battery voltage applied to terminals 1B-2 and 1B-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


11. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A182109E02
A164717E04
  1. Disconnect the HO2 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C20-2 (+B) - Body ground
    Engine switch on (IG)
    9 to 14 V
    C56-2 (+B) - Body ground
    Engine switch on (IG)
    9 to 14 V

  1. Turn the engine switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C20-1 (HT1B) - C45-45 (HT1B)
    Always
    Below 1 Ω
    C20-3 (OX1B) - C45-114 (OX1B)
    Always
    Below 1 Ω
    C20-4 (E1) - C45-115 (EX1B)
    Always
    Below 1 Ω
    C56-1 (HT2B) - C45-44 (HT2B)
    Always
    Below 1 Ω
    C56-3 (OX2B) - C45-112 (OX2B)
    Always
    Below 1 Ω
    C56-4 (E1) - C45-113 (EX2B)
    Always
    Below 1 Ω
    C20-1 (HT1B) or C45-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    C20-3 (OX1B) or C45-114 (OX1B) - Body ground
    Always
    10 kΩ or higher
    C56-1 (HT2B) or C45-44 (HT2B) - Body ground
    Always
    10 kΩ or higher
    C56-3 (OX2B) or C45-112 (OX2B) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C20-1 (HT1B) - C46-45 (HT1B)
    Always
    Below 1 Ω
    C20-3 (OX1B) - C46-114 (OX1B)
    Always
    Below 1 Ω
    C20-4 (E1) - C46-115 (EX1B)
    Always
    Below 1 Ω
    C56-1 (HT2B) - C46-44 (HT2B)
    Always
    Below 1 Ω
    C56-3 (OX2B) - C46-112 (OX2B)
    Always
    Below 1 Ω
    C56-4 (E1) - C46-113 (EX2B)
    Always
    Below 1 Ω
    C20-1 (HT1B) or C46-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    C20-3 (OX1B) or C46-114 (OX1B) - Body ground
    Always
    10 kΩ or higher
    C56-1 (HT2B) or C46-44 (HT2B) - Body ground
    Always
    10 kΩ or higher
    C56-3 (OX2B) or C46-112 (OX2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR (Click here)

12. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


13. PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

  1. Drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using second gear to decelerate the vehicle.A166582E06



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK

END

14. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15. PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Clear the DTCs.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

  1. Drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using second gear to decelerate the vehicle.A166582E06



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK

END


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (Sep 2011 – Dec 2011)P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (Sep 2011 – Dec 2011) →