All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
The main body ECU receives switch signals from the multiplex network master switch, and driver side door key cylinder switch signals from the front door lock. The main body ECU activates the door lock motor on each door according to these signals.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
| 1. CHECK DOOR LOCK OPERATION |
| Result |
Proceed to |
| All doors cannot be locked through multiplex network master switch and driver side door key cylinder |
A |
| All doors cannot be locked through multiplex network master switch (for Models with Jam Protection Function on Driver Door Window Only) |
B |
| All doors cannot be locked through multiplex network master switch (for Models with Jam Protection Function on 4 Windows) |
C |
| All doors cannot be locked through driver side door key cylinder |
D |
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) |
Disconnect the 2A, 2B and 2D main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage :
Tester Connection
Condition
Specified Condition
2A-1 (ALTB) - Body ground
Always
11 to 14 V
2B-20 (BATB) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-62 (GND2) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - MAIN BODY ECU AND BODY GROUND) |
for LHD:
Disconnect the I31 master switch connector.
Disconnect the 2D main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I31-9 (UL) - 2D-52 (UL1)
Always
Below 1 Ω
I31-2 (L) - 2D-49 (L1)
Always
Below 1 Ω
I31-1 (E) - Body ground
Always
Below 1 Ω
I31-9 (UL) - Body ground
Always
10 kΩ or higher
I31-2 (L) - Body ground
Always
10 kΩ or higher
for RHD:
Disconnect the I26 master switch connector.
Disconnect the 2D main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I26-8 (UL) - 2D-52 (UL1)
Always
Below 1 Ω
I26-2 (L) - 2D-49 (L1)
Always
Below 1 Ω
I26-9 (E) - Body ground
Always
Below 1 Ω
I26-8 (UL) - Body ground
Always
10 kΩ or higher
I26-2 (L) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (OPERATION) |
Replace the multiplex network master switch with a normally functioning one (Click here).
Check that all doors can be locked and unlocked by using the multiplex network master switch.
- OK:
- All doors can be locked and unlocked with multiplex network master switch.
|
|
||||
| OK | ||
| ||
| 5. READ VALUE USING INTELLIGENT TESTER (DOOR KEY LINKED LOCK AND UNLOCK SWITCH) |
Use the Data List to check if the door key linked lock and unlock switches are functioning properly.
Main Body ECU Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key Linked Lock SW
Door key linked lock switch signal / ON or OFF
ON: Driver side door key cylinder turned to lock position
OFF: Driver side door key cylinder not turned
-
Door Key Linked Unlock SW
Door key linked unlock switch signal / ON or OFF
ON: Driver side door key cylinder turned to unlock position
OFF: Driver side door key cylinder not turned
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK - MAIN BODY ECU AND BODY GROUND) |
for LHD:
Disconnect the I14 door lock connector.
Disconnect the E1 and 2D main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I14-10 (UL) - E1-10 (UL3)
Always
Below 1 Ω
I14-9 (L) - 2D-53 (L2)
Always
Below 1 Ω
I14-7 (E) - Body ground
Always
Below 1 Ω
I14-10 (UL) - Body ground
Always
10 kΩ or higher
I14-9 (L) - Body ground
Always
10 kΩ or higher
for RHD:
Disconnect the I6 door lock connector.
Disconnect the E1 and 2D main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I6-5 (UL) - E1-10 (UL3)
Always
Below 1 Ω
I6-6 (L) - 2D-53 (L2)
Always
Below 1 Ω
I6-8 (E) - Body ground
Always
Below 1 Ω
I6-5 (UL) - Body ground
Always
10 kΩ or higher
I6-6 (L) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY LINKED LOCK AND UNLOCK SWITCH) |
for LHD (w/o Double Locking Function):


Remove the front door lock LH (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
9 (L) - 7 (E)
Lock
Below 1 Ω
9 (L) - 7 (E)
Off
10 kΩ or higher
10 (UL) - 7 (E)
Unlock
Below 1 Ω
10 (UL) - 7 (E)
Off
10 kΩ or higher
for LHD (w/ Double Locking Function):


Remove the front door lock LH (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
9 (L) - 7 (E)
Lock
Below 1 Ω
9 (L) - 7 (E)
Off
10 kΩ or higher
10 (UL) - 7 (E)
Unlock
Below 1 Ω
10 (UL) - 7 (E)
Off
10 kΩ or higher
for RHD (w/o Double Locking Function):


Remove the front door lock RH (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
5 (UL) - 8 (E)
Unlock
Below 1 Ω
5 (UL) - 8 (E)
Off
10 kΩ or higher
6 (L) - 8 (E)
Lock
Below 1 Ω
6 (L) - 8 (E)
Off
10 kΩ or higher
for RHD (w/ Double Locking Function):


Remove the front door lock LH (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
5 (UL) - 8 (E)
Unlock
Below 1 Ω
5 (UL) - 8 (E)
Off
10 kΩ or higher
6 (L) - 8 (E)
Lock
Below 1 Ω
6 (L) - 8 (E)
Off
10 kΩ or higher
|
|
||||
| OK | ||
| ||
