Pre-heating Control Circuit
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the engine switch is turned on (IG). The ECM then turns on the glow relay and permits current to flow through the glow plug based on the ECM calculated time. The glow plug is then heated, and enhances fuel combustion with a cold engine.A DTC will be stored if the glow plug or the circuit is open.


- HINT:
- These troubleshooting procedures are for: 1) difficult engine starting in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after engine is started.
- After the engine is started, the ECM performs "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.
- These troubleshooting procedures are for: 1) difficult engine starting in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after engine is started.


WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
| 1. CHECK ECM TERMINAL VOLTAGE (GREL TERMINAL) |
Remove the GLOW 1 relay from the engine room relay block.

Remove the GLOW 2 relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
GLOW 1 relay (2) - Body ground
Engine switch on (IG)
11 to 14 V
GLOW 2 relay (2) - Body ground
Engine switch on (IG)
11 to 14 V
|
|
||||
| OK | |
| 2. INSPECT GLOW RELAY (GLOW 1 or 2) |
Inspect the GLOW 1 relay (Click here).
Inspect the GLOW 2 relay (Click here).
|
|
||||
| OK | |
| 3. INSPECT FUSE (GLOW 1 and GLOW 2) |
![]() ![]() |
Remove the GLOW 1 and GLOW 2 fuses from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Component
Condition
Specified Condition
GLOW 1 H-fuse
Always
Below 1 Ω
GLOW 2 H-fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE) |
Inspect the glow plug assembly (Click here).
|
|
||||
| OK | |
| 5. CHECK GLOW PLUG ASSEMBLY (INSTALLATION) |
Check the glow plug installation (Click here).
- OK:
- Glow plugs are installed securely.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - GLOW PLUG - BATTERY AND BODY GROUND) |
Remove the GLOW 1 relay from the engine room relay block.

Disconnect the C77 glow plug connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
No. 1 Tester Connection
Condition
Specified Condition
GLOW 1 relay (3) - C77-1
Always
Below 1 Ω
GLOW 1 relay (5) - Positive (+) battery terminal cable
Always
Below 1 Ω
GLOW 1 relay (1) - Body ground
Always
Below 1 Ω
Remove the GLOW 2 relay from the engine room relay block.
Disconnect the C78 glow plug connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
No. 2 Tester Connection
Condition
Specified Condition
GLOW 2 relay (3) - C78-1
Always
Below 1 Ω
GLOW 2 relay (5) - Positive (+) battery terminal cable
Always
Below 1 Ω
GLOW 2 relay (1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND) |
Remove the GLOW 1 relay from the engine room relay block.


Remove the GLOW 2 relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
GLOW 1 relay (2) - A38-12 (GREL)
Always
Below 1 Ω
GLOW 2 relay (2) - A38-23 (GRL2)
Always
Below 1 Ω
GLOW 1 relay (2) or A38-12 (GREL) - Body ground
Always
10 kΩ or higher
GLOW 2 relay (2) or A38-23 (GRL2) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
GLOW 1 relay (2) - A52-12 (GREL)
Always
Below 1 Ω
GLOW 2 relay (2) - A52-23 (GRL2)
Always
Below 1 Ω
GLOW 1 relay (2) or A52-12 (GREL) - Body ground
Always
10 kΩ or higher
GLOW 2 relay (2) or A52-23 (GRL2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

