2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror)

  1. B252107E03
    Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 1 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 2 (MH)
    Battery negative (-) → Terminal 1 (M+)
    Turns left (C)
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 2 (MH)
    Turns right (D)

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B302376E01
    w/ Side Turn Signal Light:

    1. Check the side turn light assembly.

    2. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Measurement Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNL)
      Negative (-) end of the battery → Terminal 5 (GND)
      Side turn light illuminates

      If the result is not as specified, check the side turn signal light assembly LH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror)

  1. B252105E03
    Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 1 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 2 (MH)
    Battery negative (-) → Terminal 1 (M+)
    Turns right (C)
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 2 (MH)
    Turns left (D)

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B302376E02
    / Side Turn Signal Light:

    1. Check the side turn light assembly.

    2. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Measurement Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNR)
      Negative (-) end of the battery → Terminal 5 (GND)
      Side turn light illuminates

      If the result is not as specified, check the side turn signal light assembly RH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror)

  1. B302415E01
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Forward position A
    Moves from A to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Forward position A
    Does not move
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Position between forward position A and driving position C
    Moves from B to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Position between forward position A and driving position C
    Moves from B to forward position A
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Driving position C
    Moves from C to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Driving position C
    Does not move
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Position between driving position C and retracted position E
    Moves from D to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Position between driving position C and retracted position E
    Moves from D to driving position C
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Retracted position E
    Does not move
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Retracted position E
    Moves from E to driving position C

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B302411E01
    Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 7 (MV)
    Battery negative (-) → Terminal 8 (M+)
    Turns upward
    Battery negative (-) → Terminal 8 (M+)
    Battery positive (+) → Terminal 7 (MV)
    Turns downward
    Battery positive (+) → Terminal 9 (MH)
    Battery negative (-) → Terminal 8 (M+)
    Turns left
    Battery negative (-) → Terminal 8 (M+)
    Battery positive (+) → Terminal 9 (MH)
    Turns right

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B302416E01
    w/ Mirror Heater:

    1. Check the mirror heater.

    2. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 6 (+) - Terminal 17 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.

    3. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (+)
      Battery negative (-) → Terminal 17 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

  1. B302375E01
    Check the side turn light assembly.

    1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Measurement Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNL)
      Negative (-) end of the battery → Terminal 15 (GND)
      Side turn light illuminates

      If the result is not as specified, check the side turn signal light assembly LH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

  1. B302413E01
    w/EC Mirror:

    1. Check the EC mirror operation.

    2. Connect 1.5 V dry-cell battery.

    3. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 5 (EC+)
      Battery negative (-) → Terminal 16 (EC-)
      Mirror surface becomes dark

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror)

  1. B302414E01
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Forward position A
    Moves from A to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Forward position A
    Does not move
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Position between forward position A and driving position C
    Moves from B to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Position between forward position A and driving position C
    Moves from B to forward position A
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Driving position C
    Moves from C to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Driving position C
    Does not move
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Position between driving position C and retracted position E
    Moves from D to retracted position E
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Position between driving position C and retracted position E
    Moves from D to driving position C
    Battery positive (+) → Terminal 19 (MR)
    Battery negative (-) → Terminal 20 (MF)
    Retracted position E
    Does not move
    Battery negative (-) → Terminal 19 (MR)
    Battery positive (+) → Terminal 20 (MF)
    Retracted position E
    Moves from E to driving position C

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B302410E01
    Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 7 (MV)
    Battery negative (-) → Terminal 8 (M+)
    Turns upward
    Battery negative (-) → Terminal 8 (M+)
    Battery positive (+) → Terminal 7 (MV)
    Turns downward
    Battery positive (+) → Terminal 9 (MH)
    Battery negative (-) → Terminal 8 (M+)
    Turns left
    Battery negative (-) → Terminal 8 (M+)
    Battery positive (+) → Terminal 9 (MH)
    Turns right

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B302417E01
    w/ Mirror Heater:

    1. Check the mirror heater.

    2. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 6 (+) - Terminal 17 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

    3. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (+)
      Battery negative (-) → Terminal 17 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

  1. B302375E02
    Check the side turn light assembly.

    1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Measurement Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNR)
      Negative (-) end of the battery → Terminal 15 (GND)
      Side turn light illuminates

      If the result is not as specified, check the side turn signal light assembly RH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

  1. B302412E01
    w/EC Mirror:

    1. Check the EC mirror operation.

    2. Connect 1.5 V dry-cell battery.

    3. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 5 (EC+)
      Battery negative (-) → Terminal 16 (EC-)
      Mirror surface becomes dark

      If the result is not as specified, replace the outer rear view mirror assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

← INSPECTION (Sep 2011 – Dec 2011)REASSEMBLY (Sep 2011 – Dec 2011) →