2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.


1. INSTALL OUTER MIRROR RETRACTOR (w/ Retract Mirror)

  1. Install the support spring

    1. B278359
      Engage the 6 claws and install the 2 support springs.

    2. Install the 2 screws.

  1. Install the wire harness

    1. B278611E01
      Pass a new wire harness through the motor and frame sub-assembly from the top, and set the marking of the wire harness to the position shown in the illustration.
      Text in Illustration 
      *a
      Marking

    2. B278351
      Connect the connector.

    3. B278349
      Install the cover.

  1. Install the actuator

    1. B278347
      Connect the connector.

    2. B278346
      Install the cover and engage the 2 clamps.

    3. B278345
      Install the actuator with the 3 screws.

  1. Install the body cover

    1. B278343E01
      Engage the 2 guides and body cover.

      NOTICE:
      Be careful not to break the guide shown in the part of the illustration labeled A.

  1. Install the body

    1. B278335
      Install the body with the 5 screws.

  1. Install the base

    1. B278333
      Engage the guide.

    2. Using "TORX" socket wrench T25, install the base with 3 new screws.

      NOTICE:
      When installing the base, check that the wire harness is not caught between the base and housing. Failure to do so may cause a short circuit.

    3. Pass the wire harness through the base.

  1. Install the lower mirror cover

    1. B278331
      Engage the 4 claws and install the new lower mirror cover.

  1. Install the gasket

    1. Pass the wire harness through the new gasket.

    2. B278327
      Engage the 9 guides and install the gasket.

    3. B278323E01
      Align the marking on the wire harness with the marking on the end of the wire harness insertion hole of the gasket as shown in the illustration, and wrap them with new vinyl tape starting from the gasket marking.
      Text in Illustration 
      *1
      New Vinyl Tape
      *a
      Marking

      NOTICE:
      If the vinyl tape is wrinkled, water may run down the wire harness and enter the vehicle. Make sure to wind the vinyl tape properly.

    4. B278325E01
      Wrap new vinyl tape as shown in the illustration.
      Text in Illustration 
      *1
      New Vinyl Tape
      *a
      Overlap

  1. Install the connector

    1. Set the retainer to the unlock position.

      B278360E01

      Text in Illustration 
      *1
      Wire Harness Pin
      -
      -
      *a
      Retainer Unlock Position
      *b
      Back View of Wire Harness Connector
      *c
      Retainer Lock Position
      -
      -
      Wire Harness 
      1
      2
      3
      4
      5
      6
      7
      8
      9
      -
      -
      Black / Blue
      *2
      Black / White
      *1
      Purple
      Red
      Brown
      Red / White
      Pink
      10
      11
      12
      13
      14
      15
      16
      17
      18
      -
      -
      Black / Red
      *2
      Black / Green
      *1
      -
      Light Blue
      White
      Gray
      Light Green
      1. *1 : w/ Heater
      2. *2 : w/ Memory

      NOTICE:
      1. When inserting the wire harness pins, compare with the connector that was cut off during removal to verify the insertion positions, and then make sure to insert the pins of the correct wire colors in the correct positions.
      2. Make sure that the wire harness pins are securely locked in position and cannot be removed.
      3. The wire harness pins cannot be removed after they have locked into place, so be absolutely certain to insert them in the correct positions.

    2. Push in the wire harness pins from the rear side of the connector until they lock into position.

    3. Twist the wire harness as shown in the illustration.

    4. B278361E01
      Wrap with new vinyl tape.
      Text in Illustration 
      *1
      New Vinyl Tape

    5. B278362
      Twist the wire harness as shown in the illustration.

    6. B278588E01
      Install a new vinyl sheet in the position shown in the illustration.

    7. B278589E01
      Install a new wire harness clamp at the marking shown in the illustration.
      Text in Illustration 
      *a
      Marking


2. INSTALL OUTER MIRROR COVER

  1. B184520
    Attach the 8 claws to install the outer mirror cover.

  1. Check that there is no gap between the cover and mirror body.

    HINT:
    If there is a gap between the cover and body, noise will occur during driving.


3. INSTALL OUTER REAR VIEW MIRROR GLASS

  1. B189668
    w/ EC Mirror:
    Connect the connector.

  1. B189669
    w/ Mirror Heater:
    Connect the 2 connectors.

  1. B183885
    Attach the 4 claws to install the mirror glass.

← INSPECTION (from Jan 2012)REASSEMBLY (from Jan 2012) →