P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0705 |
When one of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
|
|
MONITOR DESCRIPTION
This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
WIRING DIAGRAM




INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever: - In P or N: ON
- Not in P or N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever: - In R: ON
- Not in R: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range)
PNP switch status/
ON or OFF
Shift lever: - In P: ON
- Not in P: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range)
PNP switch status/
ON or OFF
Shift lever: - In N: ON
- Not in N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever: - In D: ON
- Not in D: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not in "-" (down-shift)
-
- In P or N: ON
| 1. CHECK HARNESS AND CONNECTOR (BK/UP LP FUSE - PARK/NEUTRAL POSITION SWITCH) |
Disconnect the park/neutral position switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C24-2 (RB) - Body ground
Engine switch on (IG)
11 to 14 V
C24-2 (RB) - Body ground
Engine switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
Disconnect the park/neutral position switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
C24-4 (B) - Body ground
Engine switch on (IG)
11 to 14 V
C24-4 (B) - Body ground
Engine switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch)
|
|
||||
| OK | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the park/neutral position switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
Shift lever in P
Below 1 Ω
2 (RB) - 1 (RL)
Shift lever in R
Below 1 Ω
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
Shift lever in N
Below 1 Ω
2 (RB) - 7 (DL)
- Shift lever in D
- Shift lever in S, "+" or "-"
Below 1 Ω
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
Shift lever not in P
10 kΩ or higher
2 (RB) - 1 (RL)
Shift lever not in R
10 kΩ or higher
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
Shift lever not in N
10 kΩ or higher
2 (RB) - 7 (DL)
- Shift lever not in D
- Shift lever not in S, "+" or "-"
10 kΩ or higher
- 2 (RB) - 6 (PL)
Text in Illustration *a
Component without harness connected
(Park/Neutral Position Switch)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (LH ECU-IG FUSE - TRANSMISSION CONTROL SWITCH) |
Disconnect the transmission control switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E52-3 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
E52-3 (IG) - Body ground
Engine switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Transmission Control Switch)
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION CONTROL SWITCH |
Disconnect the transmission control switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (IG) - 7 (S)
Shift lever in S, "+" or "-"
Below 1 Ω
3 (IG) - 7 (S)
Shift lever not in S, "+" or "-"
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Transmission Control Switch)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM) |
![]() ![]() |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Condition
Specified Condition
C45-2 (P) - Body ground
- Engine switch on (IG)
- Shift lever in P
11 to 14 V
C45-26 (R) - Body ground
- Engine switch on (IG)
- Shift lever in R
11 to 14 V*
C45-25 (N) - Body ground
- Engine switch on (IG)
- Shift lever in N
11 to 14 V
C45-27 (D) - Body ground
- Engine switch on (IG)
- Shift lever in D
11 to 14 V
A38-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever in S, "+" or "-"
11 to 14 V
C45-2 (P) - Body ground
- Engine switch on (IG)
- Shift lever not in P
Below 1 V
C45-26 (R) - Body ground
- Engine switch on (IG)
- Shift lever not in R
Below 1 V
C45-25 (N) - Body ground
- Engine switch on (IG)
- Shift lever not in N
Below 1 V
C45-27 (D) - Body ground
- Engine switch on (IG)
- Shift lever not in D
Below 1 V
A38-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever not in S, "+" or "-"
Below 1 V
- Engine switch on (IG)
for RHD Tester Connection
Condition
Specified Condition
C46-2 (P) - Body ground
- Engine switch on (IG)
- Shift lever in P
11 to 14 V
C46-26 (R) - Body ground
- Engine switch on (IG)
- Shift lever in R
11 to 14 V*
C46-25 (N) - Body ground
- Engine switch on (IG)
- Shift lever in N
11 to 14 V
C46-27 (D) - Body ground
- Engine switch on (IG)
- Shift lever in D
11 to 14 V
A52-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever in S, "+" or "-"
11 to 14 V
C46-2 (P) - Body ground
- Engine switch on (IG)
- Shift lever not in P
Below 1 V
C46-26 (R) - Body ground
- Engine switch on (IG)
- Shift lever not in R
Below 1 V
C46-25 (N) - Body ground
- Engine switch on (IG)
- Shift lever not in N
Below 1 V
C46-27 (D) - Body ground
- Engine switch on (IG)
- Shift lever not in D
Below 1 V
A52-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever not in S, "+" or "-"
Below 1 V
- Engine switch on (IG)
- HINT:
- *: The voltage will drop slightly due to the turning on of the back up light.
| *1 |
for LHD |
| *2 |
for RHD |
| *a |
Front view of wire harness connector (to ECM) |
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the C24 park/neutral position switch connector.
Disconnect the C45 ECM connector (for LHD).
Disconnect the C46 ECM connector (for RHD).
Measure the voltage according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
C24-4 (B) - C45-120 (NSW)
Always
Below 1 Ω
C24-4 (B) or C45-120 (NSW) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C24-4 (B) - C46-120 (NSW)
Always
Below 1 Ω
C24-4 (B) or C46-120 (NSW) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

