Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
Air Conditioning Compressor Magnetic Clutch Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the air conditioning amplifier assembly is turned on, a magnetic clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the magnetic clutch relay turns on to operate the magnetic clutch. WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK CAN COMMUNICATION SYSTEM
Check for CAN communication system DTCs related to the air conditioning system.
Result
Result
Proceed to
CAN DTC is not output
A
CAN DTC is output (for LHD)
B
CAN DTC is output (for RHD)
C
B
C
A
2. READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
Use the Data List to check if the A/C switch is functioning properly.
Engine
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/C Signal
A/C signal / ON or OFF
ON: A/C switch on OFF: A/C switch off
-
OK:
The display is as specified in the normal condition.
NG
OK
3. INSPECT FUSE (A/C IG)
Remove the A/C IG fuse from the cowl side junction block LH.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A/C IG fuse
Always
Below 1 Ω
NG
OK
4. INSPECT MAGNETIC CLUTCH RELAY
Remove the magnetic clutch relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Voltage not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
Voltage applied to terminals 1 and 2
Below 1 Ω
Install the magnetic clutch relay to the engine room relay block.
NG
REPLACE MAGNETIC CLUTCH RELAY
OK
5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
w/ Rear Heater
Disconnect the E36 amplifier connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E36-18 (MGC) - Body ground
Engine switch off
Below 1 V
E36-18 (MGC) - Body ground
Engine switch on (IG)
11 to 14 V
w/o Rear Heater
Disconnect the E81 amplifier connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E81-20 (MGC) - Body ground
Engine switch off
Below 1 V
E81-20 (MGC) - Body ground
Engine switch on (IG)
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
w/ Rear Heater
Reconnect the E36 amplifier connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E36-18 (MGC) - Body ground
Engine switch on (IG) A/C switch off
11 to 14 V
E36-18 (MGC) - Body ground
Engine switch on (IG) A/C switch on
Below 1 V
w/o Rear Heater
Reconnect the E81 amplifier connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E81-20 (MGC) - Body ground
Engine switch on (IG) A/C switch off
11 to 14 V
E81-20 (MGC) - Body ground
Engine switch on (IG) A/C switch on
Below 1 V
NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here )
OK
7. INSPECT COOLER COMPRESSOR ASSEMBLY
Disconnect the C30 compressor connector.
Disconnect the A magnetic clutch connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
C30-3 (MG+) - A-1
Always
Below 1 Ω
C30-3 (MG+) - Body ground
Always
10 kΩ or higher
NG
OK
8. INSPECT MAGNETIC CLUTCH
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A-1 - Body ground
20°C (68°F)
3.4 to 3.8 Ω
When connector terminal A-1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the operating sound of the magnetic clutch can be heard, and 2) the hub and rotor of the magnetic clutch lock.
NG
OK
9. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
Remove the magnetic clutch relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
Relay block magnetic clutch relay terminal 5 - Body ground
Engine switch on (IG)
11 to 14 V
Relay block magnetic clutch relay terminal 1 - Body ground
Engine switch on (IG)
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - COOLER COMPRESSOR)