2011-2013 Land Cruiser · Service Manual Vehicle Interior

Air Conditioning Compressor Magnetic Clutch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnetic clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the magnetic clutch relay turns on to operate the magnetic clutch.

WIRING DIAGRAM

E158696E02
E158696E03

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check for CAN communication system DTCs related to the air conditioning system.

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD)
    B
    CAN DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
  1. Use the Data List to check if the A/C switch is functioning properly.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    A/C signal / ON or OFF
    ON: A/C switch on
    OFF: A/C switch off
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 3
OK

REPLACE ECM (Click here)

3. INSPECT FUSE (A/C IG)
  1. Remove the A/C IG fuse from the cowl side junction block LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (A/C IG)
OK


4. INSPECT MAGNETIC CLUTCH RELAY

  1. B060778E04
    Remove the magnetic clutch relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Install the magnetic clutch relay to the engine room relay block.



NG
REPLACE MAGNETIC CLUTCH RELAY
OK


5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

  1. E157362E07
    w/ Rear Heater
    1. Disconnect the E36 amplifier connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E36-18 (MGC) - Body ground
      Engine switch off
      Below 1 V
      E36-18 (MGC) - Body ground
      Engine switch on (IG)
      11 to 14 V

  1. E160308E02
    w/o Rear Heater
    1. Disconnect the E81 amplifier connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E81-20 (MGC) - Body ground
      Engine switch off
      Below 1 V
      E81-20 (MGC) - Body ground
      Engine switch on (IG)
      11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E157374E03
    w/ Rear Heater
    1. Reconnect the E36 amplifier connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E36-18 (MGC) - Body ground
      Engine switch on (IG)
      A/C switch off
      11 to 14 V
      E36-18 (MGC) - Body ground
      Engine switch on (IG)
      A/C switch on
      Below 1 V

  1. E160445E01
    w/o Rear Heater
    1. Reconnect the E81 amplifier connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E81-20 (MGC) - Body ground
      Engine switch on (IG)
      A/C switch off
      11 to 14 V
      E81-20 (MGC) - Body ground
      Engine switch on (IG)
      A/C switch on
      Below 1 V



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


7. INSPECT COOLER COMPRESSOR ASSEMBLY

  1. E160585E01
    Disconnect the C30 compressor connector.

  1. Disconnect the A magnetic clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C30-3 (MG+) - A-1
    Always
    Below 1 Ω
    C30-3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
OK


8. INSPECT MAGNETIC CLUTCH

  1. E157386E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - Body ground
    20°C (68°F)
    3.4 to 3.8 Ω

  1. When connector terminal A-1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the operating sound of the magnetic clutch can be heard, and 2) the hub and rotor of the magnetic clutch lock.



NG
REPLACE MAGNETIC CLUTCH
OK


9. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)

  1. E157043E01
    Remove the magnetic clutch relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Relay block magnetic clutch relay terminal 5 - Body ground
    Engine switch on (IG)
    11 to 14 V
    Relay block magnetic clutch relay terminal 1 - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - COOLER COMPRESSOR)


← Heater Control Switch Circuit (from Jan 2012)Air Conditioning Compressor Magnetic Clutch Circuit (from Jan 2012) →