2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Driver Side Power Window does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the multiplex network master switch, power window regulator motor, harness or connector.

WIRING DIAGRAM

B292713E01

INSPECTION PROCEDURE


1. CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2. CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MOTOR)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver side power window manual up signal / ON or OFF
    ON: Driver side power window manual up switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Down SW
    Driver side power window manual down signal / ON or OFF
    ON: Driver side power window manual down switch operated
    OFF: Driver side power window switch not operated
    -

    OK:
    The display changes according to operation of the multiplex network master switch.

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
Go to step 4
A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)

  1. B276330E23
    Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I31-6 (B) - Body ground
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I26-6 (B) - Body ground
    Always
    11 to 14 V


    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I31-1 (E) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I26-9 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Multiplex Network Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)

  1. B291666E03
    Disconnect the I12*1 or I4*2 front power window regulator motor assembly connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I12-2 (B) - Body ground
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I4-2 (B) - Body ground
    Always
    11 to 14 V


    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I12-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I4-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Motor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.

  1. Disconnect the I12*1 or I4*2 front power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I31-8 (U) - I12-10 (UP)
    Always
    Below 1 Ω
    I31-5 (D) - I12-7 (DOWN)
    Always
    Below 1 Ω
    I31-4 (AUTO) - I12-4 (AUTO)
    Always
    Below 1 Ω
    I31-3 (LED+) - I12-5 (LED)
    Always
    Below 1 Ω
    I31-1 (E) - I12-1 (GND)
    Always
    Below 1 Ω
    I31-8 (U) or I12-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I31-5 (D) or I12-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I31-4 (AUTO) or I12-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    I31-3 (LED+) or I12-5 (LED) - Body ground
    Always
    10 kΩ or higher
    I31-1 (E) or I12-1 (GND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I26-1 (U) - I4-10 (UP)
    Always
    Below 1 Ω
    I26-5 (D) - I4-7 (DOWN)
    Always
    Below 1 Ω
    I26-4 (AUTO) - I4-4 (AUTO)
    Always
    Below 1 Ω
    I26-3 (LED+) - I4-5 (LED)
    Always
    Below 1 Ω
    I26-9 (E) - I4-1 (GND)
    Always
    Below 1 Ω
    I26-1 (U) or I4-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I26-5 (D) or I4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I26-4 (AUTO) or I4-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    I26-3 (LED+) or I4-5 (LED) - Body ground
    Always
    10 kΩ or higher
    I26-9 (E) or I4-1 (GND) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
Go to step 8

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


7. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B175750E17
    Remove the front power window regulator motor assembly LH (Click here).
    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counter clockwise

  1. Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    1. Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.
    1. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

  1. Apply negative (-) battery voltage to connector terminals 1 (GND), and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)

8. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

  1. B180611E16
    Remove the front power window regulator motor assembly RH (Click here).
    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counter clockwise

  1. Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    1. Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.
    1. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND), and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.
    Motor gear rotates counterclockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.
    Motor gear rotates clockwise (Down)



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)


← Driver Side Power Window does not Operate with Power Window Master Switch (Sep 2011 – Dec 2011)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (Sep 2011 – Dec 2011) →