2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the power window regulator switch assembly, front power window regulator motor assembly LH*1 or RH*2, multiplex network master switch assembly or harness or connector.
  1. *1: for LHD
  2. *2: for RHD

WIRING DIAGRAM

B292714E01

INSPECTION PROCEDURE


1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B107881E07
    Remove the power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    2 (SD) - 1 (D)
    5 (SU) - 4 (U)
    OFF
    Below 1 Ω
    2 (SD) - 1 (D)
    5 (SU) - 4 (U)
    DOWN
    Below 1 Ω
    3 (B) - 1 (D)



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. Remove the front passenger side power window regulator motor assembly (Click here).B272442E03

  1. Apply battery voltage to the motor connector according to the table below.

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Motor Gear
    -
    -
    *a
    Counterclockwise
    *b
    Clockwise

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BATTERY)

  1. B291669E05
    Disconnect the I28*1 or I30*2 power window regulator switch assembly connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I28-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I30-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the I28*1 or I30*2 power window regulator motor assembly connector.

  1. Disconnect the I27*1 or I29*2 front power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I28-4 (U) - I27-2
    Always
    Below 1 Ω
    I28-1 (D) - I27-1
    Always
    Below 1 Ω
    I28-4 (U) or I27-2 - Body ground
    Always
    10 KΩ or higher
    I28-1 (D) or I27-1 - Body ground
    Always
    10 KΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I30-4 (U) - I29-2
    Always
    Below 1 Ω
    I30-1 (D) - I29-1
    Always
    Below 1 Ω
    I30-4 (U) or I29-2 - Body ground
    Always
    10 KΩ or higher
    I30-1 (D) or I29-1 - Body ground
    Always
    10 KΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - MULTIPLEX NETWORK MASTER SWITCH)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the I28*1 or I30*2 power window regulator switch assembly connector.

  1. Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I28-5 (SU) - I31-16 (U)
    Always
    Below 1 Ω
    I28-2 (SD) - I31-15 (D)
    Always
    Below 1 Ω
    I28-5 (SU) or I30-16 (U) - Body ground
    Always
    10 kΩ or higher
    I28-2 (SD) or I30-15 (D) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I30-5 (SU) - I26-12 (U)
    Always
    Below 1 Ω
    I30-2 (SD) - I26-13 (D)
    Always
    Below 1 Ω
    I30-5 (SU) or I26-12 (U) - Body ground
    Always
    10 kΩ or higher
    I30-2 (SD) or I26-13 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)


← Driver Side Power Window does not Operate with Power Window Master Switch (from Jan 2012)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Jan 2012) →