Front Passenger Side Door Entry Lock Function does not Operate
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle (entry lock switch) → front passenger side door electrical key oscillator).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Door Lock Position SW
Front passenger side door lock position switch signal / ON or OFF
ON: Front passenger side door unlocked
OFF: Front passenger side door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH) |
Using the intelligent tester, read the Data List.
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P-Door Trigger Switch
Front passenger side door outside handle lock switch / ON or OFF
ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the z22 or z24 oscillator connector.

Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
z22-9 (TRG-) - z21-1 (TRG-)
Always
Below 1 Ω
z22-9 (TRG-) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
z24-9 (TRG-) - z23-1 (TRG-)
Always
Below 1 Ω
z24-9 (TRG-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the E29 ECU connector.

Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
E29-4 (TSW2) - z21-3 (TRG+)
Always
Below 1 Ω
E29-4 (TSW2) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
E29-4 (TSW2) - z23-3 (TRG+)
Always
Below 1 Ω
E29-4 (TSW2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
z21-1 (TRG-) - z21-3 (TRG+)
Lock switch not pushed
10 kΩ or higher
Lock switch pushed
Below 1 Ω
- for RHD:
Tester Connection
Switch Condition
Specified Condition
z23-1 (TRG-) - z23-3 (TRG+)
Lock switch not pushed
10 kΩ or higher
Lock switch pushed
Below 1 Ω
|
|
||||
| OK | |
| 7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
