2011-2013 Land Cruiser · Service Manual Vehicle Interior

Driver Side Door Entry Lock Function does not Operate

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the driver side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → driver side door outside handle (entry lock switch) → driver side door electrical key oscillator).

WIRING DIAGRAM

B186276E05

INSPECTION PROCEDURE


1. CHECK POWER DOOR LOCK OPERATION
  1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Lock Position SW
    Driver side door lock position switch signal / ON or OFF
    ON: Driver side door unlocked
    OFF: Driver side door locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)
  1. Using the intelligent tester, read the Data List.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Trigger Switch
    Driver side door outside handle lock switch / ON or OFF
    ON: Entry lock switch pushed
    OFF: Entry lock switch not pushed
    -

    OK:
    On tester screen, item changes between ON and OFF according to above chart.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B164339E51
    Disconnect the z24 or z22 oscillator connector.

  1. Disconnect the z23 or z21 handle connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z24-9 (TRG-) - z23-1 (TRG-)
    Always
    Below 1 Ω
    z24-9 (TRG-) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z22-9 (TRG-) - z21-1 (TRG-)
    Always
    Below 1 Ω
    z22-9 (TRG-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE)

  1. B187977E03
    Disconnect the E29 ECU connector.

  1. Disconnect the z23 or z21 handle connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    E29-3 (TSW1) - z23-3 (TRG+)
    Always
    Below 1 Ω
    E29-3 (TSW1) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    E29-3 (TSW1) - z21-3 (TRG+)
    Always
    Below 1 Ω
    E29-3 (TSW1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT FRONT DOOR OUTSIDE HANDLE (for Driver Side)

  1. B190958E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    z23-1 (TRG-) - z23-3 (TRG+)
    Lock switch not pushed
    10 kΩ or higher
    Lock switch pushed
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    z21-1 (TRG-) - z21-3 (TRG+)
    Lock switch not pushed
    10 kΩ or higher
    Lock switch pushed
    Below 1 Ω



NG
REPLACE FRONT DOOR OUTSIDE HANDLE (Click here)
OK


7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry function operates normally.

    OK:
    Operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)


← Driver Side Door Entry Lock Function does not Operate (Sep 2011 – Dec 2011)Front Passenger Side Door Entry Lock Function does not Operate (Sep 2011 – Dec 2011) →