2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when: 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.
DTC Code
Detection Condition
Trouble Area
B2278
Communication is abnormal between the main body ECU and engine switch or the engine switch is defective.
  1. Main body ECU
  2. Engine switch
  3. Harness or connector

WIRING DIAGRAM

C164712E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2)
  1. Use the Data List to check if the engine switch is functioning properly.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch 1
    Start Switch 1/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    Start Switch 2
    Start Switch 2/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    When the engine switch is turned on (IG), ON is displayed on the intelligent tester.



NG
Go to step 3
OK


2. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG), and check whether DTC B2278 is output.

    Result 
    Result
    Proceed to
    No DTC output
    A
    DTC B2278 output
    B



B
REPLACE MAIN BODY ECU
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT ENGINE SWITCH
C164809E03
  1. Disconnect the E18 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Within specified range
    A
    Outside specified range (for 1GR-FE)
    B
    Outside specified range (for 1UR-FE)
    C
    Outside specified range (for 3UR-FE)
    D
    Outside specified range (for 1VD-FTV)
    E



B
REPLACE ENGINE SWITCH (Click here)

C
REPLACE ENGINE SWITCH (Click here)

D
REPLACE ENGINE SWITCH (Click here)

E
REPLACE ENGINE SWITCH (Click here)
A


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)
C162990E03
  1. Disconnect the E1 main body ECU connector.

  1. Disconnect the E18 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-17 (SSW1) - E18-7 (SS1)
    Always
    Below 1 Ω
    E1-16 (SSW2) - E18-2 (SS2)
    Always
    Below 1 Ω
    E18-5 (GND) - Body ground
    Always
    Below 1 Ω
    E1-17 (SSW1) or E18-7 (SS1) - Body ground
    Always
    10 kΩ or higher
    E1-16 (SSW2) or E18-2 (SS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2278 Engine Switch Circuit Malfunction (Sep 2011 – Dec 2011)B2281 "P" Signal Malfunction (Sep 2011 – Dec 2011) →